background image

EN-16     

                                        Valor™ 2000W Series

 

 

FCC Note 

This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his 
own expense. 

 

Industry Canada Note 

This Class B digital apparatus complies with Canadian ICES-003. 

 

ISO 9001 Registration 

In 1994, OHAUS Corporation, USA, was awarded a certificate of registration to ISO 
9001 by Bureau Veritus Quality International (BVQI), confirming that the OHAUS 
quality management system is compliant with the ISO 9001 standard’s 
requirements.  On June 21, 2012, OHAUS Corporation, USA, was re-registered to 
the ISO 9001:2008 standard. 

 

 

 

Limited Warranty

 

OHAUS products are warranted against defects in materials and workmanship from 
the date of delivery through the duration of the warranty period. During the warranty 
period OHAUS will repair, or, at its option, replace any component(s) that proves to 
be defective at no charge, provided that the product is returned, freight prepaid, to 
OHAUS. This warranty does not apply if the product has been damaged by accident 
or misuse, exposed to radioactive or corrosive materials, has foreign material 
penetrating to the inside of the product, or as a result of service or modification by 
other than OHAUS. In lieu of a properly returned warranty registration card, the 
warranty period shall begin on the date of shipment to the authorized dealer. No 
other express or implied warranty is given by OHAUS Corporation. OHAUS 
Corporation shall not be liable for any consequential damages. 
As warranty legislation differs from state to state and country to country, please 
contact your local OHAUS dealer for further details.

 

 
 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for Valor 2000W Series


















Reviews: