Ofs APTOS Installation Instructions Manual Download Page 14

Page: 14 / 18

INSTRUCTIONS

ALIGN FLUSH

TO BACK EDGE

Stack-EM-Pak

TWO-SIDED TAPE

Flush to bottom

edge of top

WORK SURFACE STORAGE INSTALLATION

Position Stak-EM-Paks (HK-7) so they are parallel and inset from the

•

edge of the back panel by at least 1/4". The rounded edge of the

Stak-EM-Pak should also be flush to the bottom edge of the top.

Mark hole locations and pre-drill 1/8" diameter x 1/4" deep pilot holes.

•

Secure Stak-EM-Paks with #8 x 5/8" pan head screws. (HK-7)

•

Peel off one side of backer on two-sided tape.

•

Apply two-sided tape to bottom of cabinet.

•

Peel off second backer.

•

Position cabinet where desired, with back edge flush

•

to the edge of the top, and set in place.

Rev:

Dwg: 2562INS

INSTRUCTIONS

ALIGN FLUSH

TO BACK EDGE

Stack-EM-Pak

TWO-SIDED TAPE

Flush to bottom

edge of top

WORK SURFACE STORAGE INSTALLATION

Position Stak-EM-Paks (HK-7) so they are parallel and inset from the

•

edge of the back panel by at least 1/4". The rounded edge of the

Stak-EM-Pak should also be flush to the bottom edge of the top.

Mark hole locations and pre-drill 1/8" diameter x 1/4" deep pilot holes.

•

Secure Stak-EM-Paks with #8 x 5/8" pan head screws. (HK-7)

•

Peel off one side of backer on two-sided tape.

•

Apply two-sided tape to bottom of cabinet.

•

Peel off second backer.

•

Position cabinet where desired, with back edge flush

•

to the edge of the top, and set in place.

Rev:

Dwg: 2562INS

PART # 1699541

INSTRUCTION SHEET # 2562INS

WORKSURFACE STORAGE

INSTALLATION INSTRUCTIONS

APTOS

1. Peel off one side of backer on two-sided tape.

2. Apply two-sided tape to bottom of cabinet.

3. Peel off second backer.

4. Position cabinet where desired, with back edge flush to the edge of the

top, and set in place.

5. Position Stak-EM-Paks (HK-7) so they are parallel and inset from the

edge of the back panel by at least 1/4". The rounded edge of the Stak-EM-

Pak should also be flush to the bottom edge of the top.

6. Mark hole locations and pre-drill 1/8" diameter x 1/4" deep pilot holes.

7. Secure Stak-EM-Paks with #8 x 5/8" pan head screws. (HK-7)

TWO-SIDED TAPE

FLUSH TO BOTTOM

EDGE OF TOP

ALIGN FLUSH

TO BACK EDGE

Summary of Contents for APTOS



















Search results

Summary of Contents for APTOS

Reviews:

Related manuals for APTOS

Brands by name

Popular brands

Ofs APTOS, Installation Instructions Manual

Search results

Summary of Contents for APTOS

Reviews:

Related manuals for APTOS

Brands by name

Popular brands