background image

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

5

Specifications

Maximum Temperature: 500°F (260°C)

Maximum Pressure: 2,000 psi (13.8 MPa)

For tests above 200°F, refer to the chart below for the appropriate pres-

sure.

Do not use nitrous oxide cartridges as pressure sources for high-

temperature, high-pressure (HTHP) aging. Under high temperature and 

pressure, nitrous oxide can detonate in the presence of grease, oil, or 

carbonaceous materials. Nitrous oxide cartridges are to be used only 

for Garrett Gas Train Carbonate Analysis.

Carbon dioxide and nitrous oxide cartridges are pressurized to approxi-

mately 900 psi at 1 atmosphere (sea level). Therefore, they should never 

be transported by airplane without proper packing because cabin de-

pressurization may cause an explosion.

If the aging cells are going to be rolled in a roller oven during a test,  

install o-rings on the outer perimeter on the top and bottom of the cells. 

Failure to do so can damage the rollers in the oven. Teflon (#175-46), 

Viton

®

 (#175-47), and Buna N (#175-54) o-rings are available.

Cell Corrosion

Test fluids under high tempreature and pressure can corrode the cell body 

and caps. Carefully inspect the cell body and calls for corrosion before and 

after each test.

Some materials are more susceptible to corrosion than other. Also, some 

fluids and additives are more corrosive than others. OFITE offers a variety of 

cell materials for different levels of corrosion resistance and cost.

Mud Volume and Pressure for 

High-Temperature Aging

Aging 

Temp. 

(°F / °C)

Water 

Vapor 

Pressure 

(psi)

Coefficient 

of

Expansion 

of Water

Suggested 

Applied 

Pressure 

(psi / kPa)

Mud

Volume in

260 mL

Cell (mL)

Volume 

with 

Teflon 

Liner

Mud 

Volume 

in 500 

mL Cell 

(mL)

Volume 

with 

Teflon 

Liner

212 / 100

14.7

1.04

25 / 172

225

130

450

326

250 / 121

30

1.06

50 / 345

225

130

450

326

300 / 149

67

1.09

100 / 690

200

116

425

308

350 / 176

135

1.12

150 / 1,034

200

116

400

289

400 / 204

247

1.16

250 / 1,724

-

-

375

271

450 / 232

423

1.20

300 / 2,069

-

-

375

253

500 / 260

680

1.27

375 / 2,586

-

-

325

235

Summary of Contents for 175-25











Reviews: