background image

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

4

Optional:

#120-76  Spare Parts for #120-75:

#120-001 

Mineral Oil, 1 Gallon, Qty: 3

#120-75-19  Paddle Assembly, Qty: 2

#120-511 

Slurry Cup Shear Pin, Qty: 10

#121-001 

Container O-rings, Qty: 8

#121-002 

Retaining Ring, Qty: 2

#120-004 

Calibration Spring, Qty: 2

#121-005 

Cap Nut

#121-008 

Thermocouple

#121-009 

Timing Belt, Qty: 2

#121-010 

Heater

#121-013 

Slurry Container

#121-014 

Container Bottom, Qty: 2

#122-074-1  Fuse, 5 Amp, 5 mm × 20 mm, Qty 6

#122-078 

Fuse, 15 Amp, 5 mm × 20 mm, Qty: 3

#120-76-1 Spare Parts for #120-75-1:

#120-001 

Mineral Oil, 1 Gallon, Qty: 3

#120-75-19  Paddle Assembly, Qty: 2

#120-511 

Slurry Cup Shear Pin, Qty: 10 

#121-001 

Container O-rings, Qty: 8

#121-002 

Retaining Ring, Qty: 2

#120-004 

Calibration Spring, Qty: 2

#121-005 

Cap Nut

#121-008 

Thermocouple

#121-009 

Timing Belt, Qty: 2

#121-010-1  Heater

#121-013 

Slurry Container

#121-014 

Container Bottom, Qty: 2

#122-073-1  Fuse, 3 Amp, 5 mm × 20 mm, Qty: 6

#122-077 

Fuse, 10 Amp, 5 mm × 20 mm, Qty: 3

#152-55 

Bath/Circulator, Refrigerated and Heated, 115 VAC, 60 Hz

#152-55-1 

Bath/Circulator, Refrigerated and Heated, 230 VAC, 50 Hz

Summary of Contents for 120-75

















Reviews: