Offroad Animal RS-TLC-200-15-ASM0 Fitting Instruction Download Page 1

Offroad Animal 

RS-TLC-200-15-ASM0 

2015+ Toyota Landcruiser 200 Series

 

Fitting Instruction 

Rock Sliders 

 

REV B 

13/5/20 

Page 

1

 of 

30

 

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT! 

 READ BEFORE INSTALLATION 

 

When installed in accordance with these instructions, the front protection bar does 
not affect the operation of the vehicles SRS airbags. 

 

This product must be installed exactly as per these instructions using only 
hardware supplied. 

 

Take a few moments to read instructions thoroughly before beginning work. 

 

In the event of damage to any bar component please contact OFFROAD ANIMAL 
to arrange repair/replacement of components. 

 

Do not use this product for any vehicle make or model other than that specified on 
these instructions. 

 

Do not remove labels from this product. 

 

This product and its fixings must not be modified in any way unless stated in these 
fitting instructions. 

 

The installation of this product is recommended for trained personnel. 

 

These instructions are correct at time of publication. OFFROAD ANIMAL cannot 
be held responsible for the impact of any changes subsequently made by the 
vehicle manufacturer. If you find something has changed please contact us to let 
us know! 

 

During installation it is the duty of the installer to check correct 
operation/clearances of all components. 

 

If Instructions are to be printed for reference in the workshop, it is recommended 
that they are printed in colour, for best legibility.  

 

Fitting time estimated 1-2 hours 

 

Summary of Contents for RS-TLC-200-15-ASM0































Reviews: