background image

 10 
 

Start with Electric Starter  

Choke of the combustion engine to be pulled, respectively lever to be turned. 
Speed control lever (5) in position “full load”. Starter key to be put into position 
“Start” and starter push button to be pressed.  As soon as it has started, open 
choke until the motor is running smoothly.  
 

Do not disconnect running motor from starter battery. 

 
 

Unlock and activate spray pistol. Warm up motor for 5 minutes at low 
pressure. Then increase up to working pressure by turning the adjusting wheel 
on the unloader valve clockwise. 

 
 

Be aware of recoil. Ensure stable foothold. 

 

 

Pressure Adjustment 

Working pressure can continuously be adjusted between high and low 
pressure by opening and closing the handle at the double lance. 

 

Counter-clockwise: 

pressure decrease

 

Clockwise:  

 

pressure increase

 

 

Pressure/Water Volume Adjustment 

Pressure and water volume can continuously be adjusted according to 
requirements by turning the knob at the unloader valve. 

 
Counter-clockwise:

 

continuous reduction of pressure and water volume 
to minimum capacity 

Clockwise: 

continuous increase of pressure and water volume 
up to maximum capacity 

 

Detergent Injection 

Only if special injector kit is installed. The injector is activated when spray 
wand is fully opened. The injection rate is 10 % of the water volume. To 
achieve a lower injection rate, detergent to be diluted (e.g. 5 % requires a 1 : 1 
dilution). 
 
Fully open valve at the double lance and activate spray pistol, so activating the 
injector which automatically feeds the detergent into the water stream. 
Detergent to be sprayed onto the object to be cleaned from the top to the 
bottom. Let it work in for several minutes. Close the valve at the double lance, 
so stopping the injector, and wash the object from the bottom to the top. Keep 
a spray distance of 10 – 20 cm. Detergent residues to be washed away com-
pletely. Detergent not to be sprayed onto warm surfaces or in direct sunlight. 
Detergent must not dry. 
 
Detergent line to be flushed after work by dipping detergent hose into clean 
water and running the machine for one minute with the valve at the double 
lance open. 
 
 

 

Summary of Contents for M 320

















Reviews: