background image

 4 
 

2. 

Safety Instructions

 

 

This instruction manual should thoroughly and completely be studied 
and considered prior to initial start-up of the unit. When strictly following 
the instructions, no danger should occur. 

 

This machine must only be operated by adult persons who are fully familiar with the 
operation and possible dangers. All relevant safety instructions laid down in this 
manual strictly to be followed. 
  

 

Protective clothing to be worn during operation. 

 

The water jet leaving the spray pistol at high velocity has a rather dangerous cutting 
effect! Therefore, the water jet never to be directed onto persons, animals or electric 
units. When starting the machine, be aware of torque and recoil. Take care of a stable 
foothold. 

 

Any repair work within the high pressure section must only be carried out by qualified 
personnel. 

 

Before opening the machine in case of malfunctions, emergency it must be switched 
of by means of the ON/OFF switch

 

The max. pressure stated on the type label must not be exceeded. The unloader 
valve opens as soon as the max. operating pressure is exceeded by 10 %. The 
unloader valve is workshop adjusted and sealed. The adjustment must not be 
changed. 

 

Unsuitable or defective high pressure hoses very often cause accidents during 
operation of high pressure cleaners. Therefore check the hoses for damages before 
any start-up. Defective high pressure hoses immediately to be replaced by original 
OERTZEN equipment. Using other materials than original OERTZEN equipment 
(union respectively hose marked with “OERTZEN”) or using materials which have not 
expressively been approved by OERTZEN in writing voids all warranty and product 
liability. 
 
Worn high pressure hoses must never be repaired and re-used. 

 

Use of repair kits, accessories and the like which are not approved by OERTZEN in 
writing, voids all warranty and product liability as well as the validity of the  
Declaration of Conformity. 
 

 

Spray pistols with delayed closing mechanism must not be used, due to danger of 
injuries. 

 

Lever in open position must never be blocked or fixed in any other way. 

 

When using spray pistols below of 750 mm length particular dangers to be 
considered. 

 

After work the spray pistol to be protected against accidental/unauthorised use by 
means of the safety lever. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for M 320

















Reviews: