background image

 15 
 

7.  

Trouble Shooting

 

 

Electrical energy can cause severe injuries. Defective electrical 
components to be immediately replaced, possible causes for accidents 
to be eliminated without delay

 

Any repair work must only be carried out by qualified personnel. 

 
Only original OERTZEN equipment to be installed, as otherwise warranty 
and Declaration of Conformity will be void, health and safety standards 
are not guaranteed. 

 
During repair or maintenance work, unit to be disconnected from 
electrical network. 
 

 

Faiure Cause 

Remedy 

Motor stops 

- Fuel tank empty 
- Motor oil low level  
- Petrol filter blocked 
- Sparking plug burnt 
- Poor water supply 

- Fill tank 
- Fill up oil up to max. mark 
- Clean/replace filter 
- Replace sparking plug 
- Replace filter. Eliminate cause  
  for water shortage, re-start unit 
  by means of On/Off switch. 

Motor does not start 

- Motor oil low level. 
- Counter pressure high 
- Battery exhausted 
- Ignition switch in position "Off" 
- Petrol cock closed 
- Choke open 
- Poor water supply. 

- Fill up oil up to max. mark. 
- Release unloader valve 
- Charge battery 
- Put switch into position "On" 
- Open petrol cock 
- Close choke 
- Check filter, ensure sufficient 
  water supply. 

Pump pressure high 

- Nozzle clogged 

- Clean remove and nozzle 

Operating pressure not achieved/ 
varies 

- Air in unit 
- Insufficient water supply 
- Nozzle worn 
- Incorrect nozzle  
- Nozzle clogged 
- Water strainer blocked 
- Unloader valve leaking 
- Suction side of pump leaking 
- Suction valves sticking 
 
 
 

-  Vent unit 
- Supply line to be min. 

” 

- Replace nozzle  
- Install correct nozzle 
- Remove/clean nozzle 
- Clean filter 
- Call service 
- Tighten hose clamps 
- Carefully loosen valves by 
   means of a screw driver, if  
   needed, remove and clean 
   valves. 

Vibrations on high pressure hose 
and spray pistol 

- Air in unit 
 

- Open handle on pistol unless   
  continuous pressure is achieved 

Heavy vibrations on unit 

- Plunger blocked 
 

- Stop unit immediately, 
  call service 

No detergent injection 

- Detergent tank empty 
- Dosing valve or regulating  
  handle closed 
- Low pressure nozzle in double 
  lance blocked 
- Non-return valve blocked 

- Fill tank 
- Open 
 
- Remove and clean nozzle 
 
- Blow compressed air into 
  detergent hose 

 

Summary of Contents for M 320

















Reviews: