Oerlikon Sogevac SV40 BI Operating Instructions Manual Download Page 12 | Manualshive

Page: 12 / 28

background image

12

GA02329_002_03 - 01/2010 - © Oerlikon Leybold Vacuum

The motor connection box integrates an ON/OFF 24 VDC relay. The pump
operation is commanded with a 24 VDC signal lead through a dedicated
cable.

The final end product must provide a 24 VDC signal (protected by a 3 A fuse) for
the remote control power relay coil. This 24 VDC signal shall be generated by a
power supply complying to IEC 61010-1: 2001 (2nd Edition) double or reinforced
insulation requirements (equivalent standards requirements like IEC60950-1) are
acceptable.

3.3 Oil filling

For SV40 BI, the necessary oil is supplied in cans beside the pump.

To fill in the oil, unscrew the oil fill plug (58) and fill in until the oil level rea-
ches the “MAX” mark beside the oil sight glass. Typically the whole 1 l oil can
is used

Installation

Caution

«
...
10
11
12
13
14
...
»

Summary of Contents for Sogevac SV40 BI





























Reviews:

No comments

Related manuals for Sogevac SV40 BI

Brand: A.O. Smith Pages: 24

Brand: ABI Attachments Pages: 20

Comfort 5000/5 LCD

Brand: Gardena Pages: 13

Brand: Grundfos Pages: 35

Brand: samhydraulik Pages: 7

ACT Signature Series

Brand: Aqua Comfort Pages: 2

Brand: Bock Water heaters Pages: 62

Brand: C.P.A. Pages: 40

HTVZD*1C series

Brand: Halsey Taylor Pages: 7

Brand: Ranpump Pages: 23

Brand: Flotec Pages: 20

SEASONCON ALP-045C

Brand: McQuay Pages: 59

Brand: Barmesa Pumps Pages: 15

Delta Plus UE 35A-XX PWM Series

Brand: WITA Pages: 36

Brand: American Water Heater Pages: 60

Brand: Walrus Pages: 6

Brand: emaux Pages: 31

Brand: Eckerle Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands