OEM TUF-2000F User Manual Download Page 6 | Manualshive

Page: 6 / 37

OEM TUF-2000F User Manual Download Page 6

TUF-2000F User Manual

6

(3) Gasoline (4) Fuel oil (5) Crude Oil
(6) Propane at -45C (7) Butane at 0C
(8)Other liquids(need to enter sound speed in M21 and viscosity in M22) (9)

Diesel Oil (10)Caster Oil (11)Peanut Oil (12) #90 Gasoline (13) #93

Gasoline (14) Alcohol (15) Hot water at 125C

M21

Window for entering the sound speed of non- standard liquid, used only when

option item 8 ‘Other’ is selected in M20

M22

Window for entering the viscosity of the non-standard liquids, used only when

option item 8 ‘Other’ is selected in M20

M23

Window for selecting transducer type, There are 22 types as following

0.       Standard M (The middle size)
1.    Insertion Type C
2.    Standard S
3.    User Type
4.    Standard B
5.    Insertion Type B(45)
6.    Standrad L          (The large size transducers)
7.    JH-Polysonics
8.    Standard-HS      (small size transducer for Handheld flow meter)
9.    Standard-HM    (middle size transducer for Handheld flow meter)
10.   Standard-M1 (middle size transducer #1)
11.   Standard-S1 (small size transducer #1)
12.    Standard-L1      (large size transducer #1)
13.   PI-Type
14.   FS410 (middle size transducer for FUJI flow meter)
15.   FS510 (large size transducer for FUJI flow meter)
16.    Clamp-on TM-1 (Middle size transducer for Taosonics Instrument)
17.    Insertion TC-1    (for Taosonic Instrument)
18.    Calmp-on TS-1    (small size for Taosonics Instrument)
19.    Reserved
20.    Clamp-on TL-1      (For Taosonics Instrument)
21.    Insertion TLC-1    (For Taosonics Instrument)

If the user-type-transducer is selected, you need enter additional 4

user-type-wedge parameters that describe the user transducers.
If the PI-type transducer is selected, you need enter additional 4 PI-type transducer

parameters that describe the PI-type transducers

M24

Window for selecting the transducer mounting methods
Four methods can be selected:
(0) V-method (1) Z-method (2) N-method (3) W-method

M25

Display the transducer mounting spacing or distance

M26

(1) A switch for the parameters in flash memory will be loaded when power is

turned on. The default option is that the parameters will be loaded. If this switch

is not turned on, the system will try to use the parameters in the system RAM, if

these parameters are ok, otherwise the system will load the parameters in

flash memory

«
...
4
5
6
7
8
...
»

Summary of Contents for TUF-2000F






































Reviews:

No comments