OEM TUF-2000F User Manual Download Page 10 | Manualshive

Page: 10 / 37

OEM TUF-2000F User Manual Download Page 10

TUF-2000F User Manual

10

For Version-15 flow meter, you need to indicate on your orders that you need the

frequency function; Otherwise you will get a flow meter which has no frequency

output circuits.

M68

Window to setup the minimum flow rate value which corresponds to the lower

frequency limit of the frequency output.

M69

Windows to setup the maximum flow Rate value that corresponds to the upper

frequency limit of the frequency output.

M70

LCD display backlight control. The entered value indicates how many seconds the

backlight will be on with every key pressing. If the enter value is great than 50000

seconds, It means that the backlight will always keeping on.

M71

LCD contrast control. The LCD will become darker or brighter when a value is

entered.

M72

Working timer. It can be cleared by pressing ENT key, and then select YES.

M73

Window to setup the lower limit of flow rate for Alarm#1.
When the flow rate is below the set value, Alarm#1 equals ‘on’

M74

Window to setup the upper limit of flow rate for Alarm#1.
When the flow rate is above the set value, Alarm#1 equals ‘on’
There are two alarms in the flow meter, and every alarm can be pointed to alarm

output devices such as the BUZZER or OCT output or RELAY output. For example,

if you want the Alarm#1 is to output by the OCT circuit, you need to set M78 at

selection item 6.

M75

Window to setup the lower limit of flow rate for Alarm#2.

M76

Window to setup the upper limit of flow rate for Alarm#2.

M77

Buzzer setup.
If a proper input source is selected, the buzzer will beep when the trigger event

occurs. The available trigger sources are:
0. No Signal                    1. Poor Signal
2. Not Ready (No*R) 3. Reverse Flow 4. AO Over 100%
5. FO Over 120% 6. Alarm #1 7. Reverse Alarm #2
8. Batch Control 9. POS Int Pulse 10.NEG Int Pulse
11.NET Int Pulse 12.Energy POS Pulse      13.Energy NEG Pulse
14.Energy NET Pulse 15.MediaVel=>Thresh 16.MediaVelo<Thresh
17.ON/OFF viaRS232 18.Daily Timer (M51) 19.Timed alarm #1
20. Timed alarm #2 21.Batch Totalizer Full 22. M51 Timer
23. Key Stroking ON 24.Disable BEEPER

M78

OCT (Open Collect Transistor Output)/OCT1 setup
By selecting a proper input source, the OCT circuit will close when the trigger event

occurs. The available trigger sources are:
0. No Signal   1. Poor Signal
2. Not Ready(No*R) 3. Reverse Flow 4. AO Over 100%
5. FO Over 120% 6. Alarm #1 7. Reverse Alarm #2
8. Batch Control 9. POS Int Pulse 10.NEG Int Pulse
11.NET Int Pulse 12.Energy POS Pulse 13.Energy NEG Pulse
14.Energy NET Pulse    15.MediaVel=>Thresh 16.MediaVelo<Thresh
17.ON/OFF viaRS232    18. Daily Timer (M51) 19.Timed alarm #1

«
...
8
9
10
11
12
...
»

Summary of Contents for TUF-2000F






































Reviews:

No comments