background image

iv

IMPORTANT SAFETY INSTRUCTIONS

1. 

Read these instructions - All these safety and operating instructions should be read before the product is operated.

2. 

Keep these instructions - The safety, operating and user instructions should be retained for future reference.

3. 

Heed all warnings - All warnings on the product and in the operating instructions should be adhered to.

4. 

Follow all instructions - All operating and user instructions should be followed.

5. 

Do not use this apparatus near water - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet 
basement; near a swimming pool; etc.

6. 

Clean only with dry cloth - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7. 

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and openings in 
the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from overheating. The 
openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not 
be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s 
instructions have been adhered to.

8. 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that 
produce heat.

9. 

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider 
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are 
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the 
obsolete outlet.

10.  Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where 

they exit from the apparatus.

11.  Only use attachments/accessories specified by the manufacturer.

12.  Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart 

is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.  Unplug this apparatus during lightning storms or when unused for long periods of time.

14.  Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, 

such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus 
has been exposed to rain or moisture, does not operate normally, or has been dropped. 

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for Black BLK-HDC10

























Reviews: