background image

1 Introduction

With your choice of the Oasis sunshade stand you have purchased a high-quality product 

featuring a patented and unique design that allows you to move the sunshade while in use 

to any spot on your terrace, while maintaining an upright posture. Finally you can put up 

the sunshade where it is really needed.

Read the information in this manual carefully so you will be able to use your sunshade 

stand safely and effectively.
We hope you enjoy your product.

2 For your safety

2.1 Intended use

The sunshade stand is intended only for use as a holding device for sunshades on a level 

and solid surface. Use only sunshades that, according to the manufacturer‘s specifications, 

are suitable for the weight class of the sunshade stand, to ensure maximum stability.
The different models of the LiRo sunshade stand may be used only for poles with the dia

-

meters specified in the Technical Data 

Model LiRo

Specified pole diameters

330R

1.77 in to 2.68 in

330R with Quick Clamp

Accessory QC2

1.97 in and 2.17 in

The sunshade stand - in moving position - can be moved together with the sunshade on a 

level surface

Foreseeable misuse

Misuse can result in dangerous situations. Therefore, never use the sunshade stand

  

as a stand for objects for which the static requirements are not known

  

with sunshades that are not suitable for the stand due to the pole diameter or 

 

size

 

for transporting persons

6 Disassembly at end of season

    At the end of the season the sunshade stand should be stored as follows:

    1.  Remove the sunshade from the mounting tube of the sunshade stand by

      –  loosening the knurled screws (model: 330R).

      –  opening the clamping lever (model: 330R with Quick Clamp Accessory).

  

Storage

    2.  Store the sunshade stand, if possible, at a location that fulfills the following criteria. 

The storage location should be:

     – dry

      –  protected against frost

     – level

  

i

 

Alternatively, you can cover the sunshade stand with an optional protective  

 

cover

      To prevent the protective cover from becoming loose, pull the cover completely    

down to the ground and then draw the rubber straps tight until they are caught  

 

under the protective cove

1 Introduction  2 

For your safety

   

2.1   Intended use

Disassembly at the end of season

4

17

Summary of Contents for 330R With QC2











Reviews: