background image

1  

Introduction    

 

 

 

 

 

  4

2  

For your safety 

 

 

 

 

 

  4

2.1   Intended use  

 

 

 

 

 

  4

2.2   Symbols in the manual    

 

 

 

  5

2.3   Safety notices 

 

 

 

 

 

  5

Scope of delivery   

 

 

 

 

  8

3.1   Unpacking the sunshade stand   

 

 

  9

4  

Assembly of the sunshade stand   

 

 

10

4.1  Assembly pictures   

 

 

 

 

10

4.2  Assembly 

 

 

 

 

 

 

13

5  

Using the sunshade stand   

 

 

 

15

5.1   Inserting the sunshade 

 

 

 

 

15

5.2   Moving the sunshade stand 

 

 

 

16

6  

Disassembly at end of season 

 

 

 

17

7  

Care    

 

 

 

 

 

 

18

8  

Disposal 

 

 

 

 

 

 

18

9  

In case of problems  

 

 

 

 

18

10   Technical data 

 

 

 

 

 

19

7   Care

  

  

 

    Scratching of the casing and mounting tube due to incorrect care! 

  

  Do not use aggressive or abrasive cleaners (such as steel wool), which can dama

-

ge the surface of the sunshade stand.

  

  Do not use highpressure or steam cleaners.

  

      Incorrect materials for cleaning and care can damage the surface of the sunshade 

stand.

  

  Clean the casing with mild soapy water and a soft cloth.

  

  Use a stainless steel cleaner for care of the mounting tube

  

i

  For rough cleaning of the casing, you can also spray it off with a garden hose.

      However, do not spray water inside the mounting tube and the base.

8   Disposa

  

 Danger to the environment due to incorrect disposal! !

  

  Dispose of all parts in accordance with waste disposal regulations. If in doubt, 

contact the responsible authority for information on correct disposal

      Incorrect disposal can result in damage to the environment and fines

    The following materials are used:

  

  The casing is made of plastic or natural fibers (rattan), depending on the model

  

  The base including the mounting tube and the clamp are made of various metals 

and plastics

  

  The weight segments are made of special concrete.

9 In case of problems

  

  Danger of injury due to damaged parts! 

  

  Never use a defective sunshade stand.

  

   If the sunshade stand is damaged, there is an increased danger that it could over

-

turn or roll away, resulting in severe injuries

  

  If you have questions concerning the product or the purchase of replacement parts, 

contact the dealer where you purchased the sunshade stand or our technical sup-

port department (see page 2 for address).

  

i

 

For questions about sunshades that can be used with the stand, contact the sun-

shade manufacturer

Table of contens

Care              8      Disposal

9  

In case of problems

18

3

Summary of Contents for 330R With QC2











Reviews: