background image

4

This engine is intended for model cars. 
Do not attempt to use it for any other 
purpose.

Mount the engine in your model 
securely, following the manufacturers' 
recommendations, using appropriate 
screws and locknuts.

Fit an effective silencer (muffler). 
Frequent close exposure to a noisy 
exhaust (especially in the case of the 
more powerful highspeed engines) 
may eventually impair your hearing 
and such noise is also likely to cause 
annoyance to others over a wide area.

The wearing of safety glasses is also 
strongly recommended.

Take care that the glowplug clip or 
battery leads do not come into contact 
with rotating parts. Also check that the 
linkage to the throttle arm is secure. 

For their safety, keep all onlookers 
(especially small children) well back 
(at least 20 feet or 6 meters) when 
preparing your model for running.

NOTES

5

NOTES

To stop the engine, fully retard the 
throttle stick and trim lever on the 
trans-mitter, or, in an emergency, cut 
off the fuel supply by pinching the fuel 
delivery line from the tank.

Warning! Immediately after a glowplug-
ignition engine has been run and is still 
warm, conditions sometimes exist 
whereby it is just possible for the engine 
to abruptly restart if it is rotated over 
compression WITHOUT the glowplug 
battery being reconnected.

Do not attempt to disassemble the 
recoil starter of the 12CV-RX. 
If you do so, the very strong spring 
inside will be suddenly ejected. This 
can be very dangerous.

Do not extend the starter cord more 
than 45cm (18"). Do not abruptly 
release the operating handle. Allow 
the cord to rewind smoothly while 
still holding the handle. 

Pull the operating handle straight out 
when starting the engine, so that the 
cord does not rub against the vehicle 
body or engine. This will help prevent 
the cord from being damaged by 
abrasion or engine heat.

Summary of Contents for MAX-15CV-R Series




















Reviews: