background image

12

A  fuel  tank  of  approximately 
360cc  capacity  is  suggested.   
This  allows  around  12  minutes  flying  time, 
dependent upon the type of fuel used, the size 
of propeller and on the amount of full-throttle to 
part-throttle operation throughout the flight.

Fuel Tank

GLOW PLUG

O.S. Type F glowplug is supplied with the engine.

GLOWPLUG IGNITER

Commercialy  available  handy 
glowplug  heater  in  which  the 
glowplug battery and battery leads are integrated. 

Alternatively, one of the 
purpose-made manual or 
electric fuel pumps may be used to transfer fuel 
directly from your fuel container to the fuel tank.

FUEL PUMP

Manual

Electric

Electric Starter and
Starter Battery

Required when starting
the engine.

12-Volt lead-acid battery

Electric
Starter

Install  a  filter  on  the  outlet  tube  of  your 
refueling  container  to  prevent  entry  of 
foreign  matter  into  fuel  tank.  O.S.  ‘Super  Filters’ 
(large and small) are available as optional extras.

O.S. Super Filter (Fuel Can Filter)

S

To  prevent  the  pickup  from  adhering  to 
the tank wall under suction and restricting 
fuel flow, slots may be filed in the end of 
the  weight.  Alternatively,  an  O.S.  Non-
Bubble Weight is available as an optional 
extra.

O.S. Non-Bubble Weight

13

It  is  recommended  to  install  a  good 
in-line  filter  between  the  fuel  tank  and 
carburetor  to  prevent  entry  of  foreign  matter 
into the carburetor.

Fuel Filter

SILICONE FUEL LINE

Heatproof silicone tubing of approx. 
5mm  o.d.  and  2.5mm  i.d.  is  required  for  the 
connection between the fuel tank and engine.

8mm

TOOLS

HEX Screwdriver

SCREWDRIVER

Necessary for engine installation.
1.5mm, 2.5mm

Necessary for carburetor adjustments.

Phillips Screwdriver

No.2, etc.

Socket Screwdriver

5mm, 5.5mm, 7mm 

LONG SOCKET WRENCH WITH PLUG GRIP

Recommended  for  easy  removal  and 
replacement  of  the  angled  and  recessed 
glowplug,  the  O.S.Long  Socket  Wrench 
incorporates a special grip.

End Wrenches

12-14mm, etc.

Needle Nose Pliers

Summary of Contents for Alpha Series






















Reviews: