NXP Semiconductors MC9S08PA4 Reference Manual Download Page 91 | Manualshive

Page: 91 / 401

background image

NVM_FSTAT field descriptions (continued)

Field

Description

0

No access error detected.

1

Access error detected.

4

FPVIOL

Flash Protection Violation Flag

The FPVIOL bit indicates an attempt was made to program or erase an address in a protected area of
flash or EEPROM memory during a command write sequence. The FPVIOL bit is cleared by writing a 1 to
FPVIOL. Writing a 0 to the FPIOL bit has no effect on FPIOL. While FPIOL is set, it is not possible to
launch a command or start a command write sequence.

0

No protection violation detected.

1

Protection violation detected.

3

MGBUSY

Memory Controller Busy Flag

The MGBUSY flag reflects the active state of the memory controller.

0

Memory controller is idle.

1

Memory controller is busy executing a flash command (CCIF = 0).

2

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

MGSTAT

Memory Controller Command Completion Status Flag

One or more MGSTAT flag bits are set if an error is detected during execution of a flash command or
during the flash reset sequence.

NOTE: Reset value can deviate from the value shown if a double bit fault is detected during the reset

sequence.

4.6.7 Flash Error Status Register (NVM_FERSTAT)

The FERSTAT register reflects the error status of internal flash and EEPROM
operations.

Address: 3020h base + 7h offset = 3027h

Bit

7

6

5

4

3

2

1

0

Read

Write

Reset

0

0

0

0

0

0

0

0

NVM_FERSTAT field descriptions

Field

Description

7–2

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

1

DFDIF

Double Bit Fault Detect Interrupt Flag

The setting of the DFDIF flag indicates that a double bit fault was detected in the stored parity and data
bits during a flash array read operation or that a flash array read operation returning invalid data was

Table continues on the next page...

Chapter 4 Memory map

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

NXP Semiconductors

91

«
...
89
90
91
92
93
...
»

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S08PA4

Brand: Accel Pages: 8

Brand: Eaton Pages: 2

Brand: Vega Pages: 20

Brand: Vacon Pages: 132

Brand: National Instruments Pages: 34

Brand: Daruifuno Pages: 24

infi 90 IMMFP12

Brand: Bailey Pages: 75

Brand: wattstopper Pages: 4

Brand: AUMA Pages: 48

OPUS A3 STANDARD Full

Brand: Topcon Pages: 10

Hauser COMPAX-M Series

Brand: Parker Pages: 84

Brand: Danfoss Pages: 44

Brand: Eaton Pages: 9

Limitorque LTQ008

Brand: Flowserve Pages: 41

Brand: Team Orion Pages: 28

Brand: MAC3 Pages: 20

Brand: BioSmart Pages: 24

Brand: Roger Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands