manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

The NXP Semiconductors MC9S08PA4 is a powerful microcontroller offering exceptional performance and versatility. To maximize your understanding and effectively utilize its features, we provide a comprehensive Reference Manual available for free download at manualshive.com, offering detailed instructions and guidelines for optimal usage.

Share
Download
background image

NVM_FERSTAT field descriptions (continued)

Field

Description

attempted on a flash block that was under a flash command operation. The DFDIF flag is cleared by
writing a 1 to DFDIF. Writing a 0 to DFDIF has no effect on DFDIF.

NOTE: The single bit fault and double bit fault flags are mutually exclusive for parity errors, meaning that

an ECC fault occurrence can be either single fault or double fault but never both. A simultaneous
access collision, when the flash array read operation is returning invalid data attempted while a
command is running, is indicated when both SFDIF and DFDIF flags are high.

NOTE: There is a one cycle delay in storing the ECC DFDIF and SFDIF fault flags in the register. At least

one NOP is required after a flash memory read before checking FERSTAT for the occurrence of
EEC errors.

0

No double bit fault detected.

1

Double bit fault detected or a flash array read operation returning invalid data was attempted while
command running.

0

SFDIF

Single Bit Fault Detect Interrupt Flag

With the IGNSF bit in the FCNFG register clear, the SFDIF flag indicates that a single bit fault was
detected in the stored parity and data bits during a flash array read operation or that a flash array read
operation returning invalid data was attempted on a flash block that was under a flash command
operation. The SFDIF flag is cleared by writing a 1 to SFDIF. Writing a 0 to SFDIF has no effect on
SRFDIF.

0

No single bit fault detected.

1

Single bit fault detected and corrected or a flash array read operation returning invalid data was
attempted while command running.

4.6.8 Flash Protection Register (NVM_FPROT)

The FPROT register defines which flash sectors are protected against program and erase
operations.

The unreserved bits of the FPROT register are writable with the restriction that the size of
the protected region can only be increased (see 

Protection

).

During the reset sequence, the FPROT register is loaded with the contents of the flash
protection byte in the flash configuration field at global address 0xFF7C located in flash
memory. To change the flash protection that will be loaded during the reset sequence, the
upper sector of the flash memory must be unprotected, then the flash protection byte must
be reprogrammed.

Trying to alter data in any protected area in the flash memory will result in a protection
violation error and the FPVIOL bit will be set in the FSTAT register. The block erase of a
flash block is not possible if any of the flash sectors contained in the same flash block are
protected.

Flash and EEPROM registers descriptions

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

92

NXP Semiconductors

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S08PA4

Yudian AI Series Operation Instruction Manual preview
AI Series
Brand: Yudian Pages: 26
Taie FY100 Communications Manual preview
FY100
Brand: Taie Pages: 28
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
OES ISC-9000 Operational Instructions preview
ISC-9000
Brand: OES Pages: 3
Mitsubishi A1SJ71E71N-B2 User Manual preview
A1SJ71E71N-B2
Brand: Mitsubishi Pages: 30
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Brand: Ros Pages: 10
Webasto SmarTemp Control fx Installation And Operation Instructions Manual preview
SmarTemp Control fx
Brand: Webasto Pages: 8
YASKAWA Lift Inverter L1000V Technical Manual preview
Lift Inverter L1000V
Brand: YASKAWA Pages: 282
A10 Networks Harmony 2000 Quick Start Manual preview
Harmony 2000
Brand: A10 Networks Pages: 2
Danfoss ECL Comfort 300 User Manual preview
ECL Comfort 300
Brand: Danfoss Pages: 75
JBSYSTEMS Light SCENE MASTER - V1.0 Operation Manual preview
SCENE MASTER - V1.0
Brand: JBSYSTEMS Light Pages: 24
CALEFFI AIR190002 Quick Start Manual preview
AIR190002
Brand: CALEFFI Pages: 14
D-M-E VCTB-4000 User Manual preview
VCTB-4000
Brand: D-M-E Pages: 15
Alcor Micro AU9540 Technical Reference Manual preview
AU9540
Brand: Alcor Micro Pages: 18
Topcon OPUS A3 Eco Get Started preview
OPUS A3 Eco
Brand: Topcon Pages: 9
KORINS EPIP-40 /30A(I) Instruction Manual preview
EPIP-40 /30A(I)
Brand: KORINS Pages: 3
Jordan Valve Mark 60 Series Installation & Maintenance Instructions preview
Mark 60 Series
Brand: Jordan Valve Pages: 5

Brands by name

Popular brands

Load more brands