background image

|

  nVent.com/ERICO

Table of Contents

1 INTRODUCTION ........................................................................................................................................................................ 3

2 WARNING .................................................................................................................................................................................. 3

3 INSTALLATION CAUTIONS ........................................................................................................................................................ 4

4 IDENTIFY THE DISTRIBUTION SYSTEM .................................................................................................................................... 5

5 MOUNTING THE SRF ................................................................................................................................................................. 8

6 OPTIMISING PERFORMANCE ................................................................................................................................................... 9

7 SERVICING AND TROUBLESHOOTING .................................................................................................................................... 16

8 BACKPLANE MODELS ............................................................................................................................................................. 18

9 SCHEMATIC DIAGRAMS ......................................................................................................................................................... 18

10 PHYSICAL DIMENSIONS ....................................................................................................................................................... 19

Summary of Contents for ERICO 5RF363N





















Reviews: