NUVE NF 1200 User Manual Download Page 15

14 

 

NOTE  3 :

 

At  hold  position,  the  rotor  keeps  spinning  until  the  STOP  key  (7)  is  pushed. 
After  the  STOP  has  been  pushed,  the  rotor  brakes  according to  the  set  brake 
rate,  

NOTE  4 :

 

The  centrifuge  waits  at  the  stand-by  position  with  the  program  values  of  the 
last program. 

NOTE  5 :

 

Please  open  the  lid  after  every  operation,  otherwise  the  centrifuge  cannot  be 
run again. 

 

4.5.  SAFETY INTERLOCK SYSTEM 

 
The safety interlock system prevents opening of the lid when the rotor is spinning. 
The  centrifuge  does  not  operate  until  the  lid  is  closed  and  the  lid  remains  locked  until  the  rotor 
stops spinning. The 

“Lid Open” indicator turns on to warn the user if the lid is not closed properly.  

 

NOTE: 

If power failure occurs, access to the samples is possible by opening the lid with a special 
tool. Please see the manual lid opening section (3.6.) for further information. 

4.6.  IMBALANCE DETECTION SYSTEM 

  The  imbalance  detection  system  of  the  NF  1200  /  NF  1200  R  centrifuges  operates 

electronically  when  an  unacceptable  imbalance  occurs.  In  this  case  the  brake  is  applied 
immediately. 

 

The “Err 1” imbalance error is displayed and the imbalance indicator turns on. The lid can not 
be  opened  until  the  rotor  stops  spinning.  The  centrifuge  can  only  be  started  after  the  lid  has 
been opened and the rotor has been re-loaded correctly.  

  To avoid facing imbalance problem, please make sure to insert the tubes correctly. 

4.7.  MANUAL LID OPENING 

In  case  of  power  cut  or  any  breakdown,  the  centrifuge  can  be  opened  manually  to  access  the 
samples. 
 
To open the lid manually: 
 

  Switch off the instrument. 

  Insert  the  manual  lid  opening  tool  into  the  hole  on  the  left  side  of  the  instrument  (see  the 

general view drawing). 

  Push the tool keeping it horizontal until the lid opens. 

 

WARNING !!! 
 

Before opening the lid manually, make sure that the rotor already stopped spinning. Upon opening 
the  lid,  lift  it  by  hand  and  observe  the  rotor.  If  the  rotor  is  still  spinning,  close  the  lid  and  wait 
approximately  10  minutes  before  repeating  the  operation.  This  operation  must  be  carried  by 
someone who is informed of the danger and of the precautions which must be undertaken.

 

 

 

Summary of Contents for NF 1200
























Reviews: