NUVE EN 032 Instruction Manual Download Page 13

13 

 

The  instruments  and  electronic  accessories  (without  batteries,  power  packs  etc.)  must  be 
disposed off according to the regulations for the disposal of electronic components. Batteries, 
power packs and similar power source have to be dismounted from electric/electronic parts and 
disposed off in accordance with applicable local regulations.  
 

9.

 

TROUBLESHOOTING 

If the incubator fails to operate, check the followings, 

 

The On/off switch is on. 

 

Fuses are sound. 

 

The plug is not defective. 

 

The plug is plugged-in properly. 

 

The installation of the plug is not defective. 

 

The mains supply is present. 

 
If the incubator does not heat, check the followings, 

 

The program is started. 

 

The safety thermostat value is adjusted higher than set temperature value. 

9.1.

 

ERROR CODES 

In  case  of  failure  during  the  operation,  the  alarm  is  activated  and  the  following  error  codes 
appear on the temperature display. 

OFL: 

The  chamber  temperature  is  higher  than  105  °C  or 

the  temperature  sensor  endings  are 

broken. 

Turn the device off and contact to the authorized service.

 

 

If an error occurs, please contact to an authorized Nüve agent to seek technical help. 

9.2.

 

FUSE REPLACEMENT 

The fuses shall be always be replaced by the authorized personnel. 

Summary of Contents for EN 032















Reviews: