FRONT PANEL FEATURES
1.
Power LED:
Illuminates when the mixer is on.
2.
Microphone Input:
Microphones with a ¼”
connector can be connected to this input
terminal.
3.
Mic Gain:
This knob adjusts the volume of the
microphone input.
4.
Tone Knob:
This rotary knob adjusts the tone.
5.
Channel Gain:
This rotary control adjusts the
pre-fader input level.
6.
Channel Treble:
This rotary control adjusts the
high-tone level.
7.
Channel Middle:
This rotary control adjusts the
middle -tone level.
8.
Channel Bass:
This rotary control adjusts the
low-tone le vel.
9.
Input Selector:
This toggles select what input
source is routed to the channel from the rear
panel connected units.
10.
Channel Fader:
This slide fader is used to adjust
the level sent to program mix.
11.
Headphone Jack:
Your headphones can be
connected to this ¼” terminal. The volume
should always be set at its lowest setting while
connecting and disconnecting headphones to
prevent damage to headphones and/or your
hearing
.
12.
Headphone Volume:
This rotary control adjusts
the volume level of the headphone outpu t.
13.
Tone Knob:
This rotary knob adjusts the tone.
14.
Cue Slider:
Channels 1 and 2 can be previewed
using this mini-crossfader. Sliding this to the left
plays the left “channel-1” and sliding to the right
plays the right “channel-2”.
15.
Replaceable Crossfader:
This slide fader blends
audio between the channels assigned to the left
and right assign switches.
Note:
This fader is user replaceable if it should
ever wear out. Simply remove the facepanel and
then remove the screws holding it in position.
Replace the fader with a quality authorized
replacement from your local Numark retailer.
16.
Crossfader Direction:
Activation of this switch
reverses the assignment of CH-1 and CH-2 on
the crossfader.
17.
Crossfader Contour Control:
The position of
this control determines how quickly or intensely
the crossfader will blend.
18.
Transform buttons:
19.
Master Output Knob :
This rotary control
adjusts the main output volume.
20.
Stereo Level Indicator:
quickly and accurately
tracks level of audio.
21.
KILL Switches:
Eliminate High, Mid, or Low
frequencies for a unique effect.
REAR PANEL FEATURES
1
4
2
3
1
5
6
7
8
2
3
Note: It is recommended that the mixer be turned
off before connecting and disconnecting any
sources to the inputs of the mixer.
1.
Phono Inputs:
This input is used for connecting
your turntables through the sensitive RIAA phono
preamplifiers. Only turntables with phono level
output should be attached. Line level turntables
and other devices may be attached if the Phono/Line
rear panel switch is set to the line position.
2.
Phono/Line Source Switch:
This switch activates
and deactivates the sensitive RIAA phono
preamplifiers.
Only turntables with phono level
output should be assigned when the switch is
in the phono position.
Some turntables offer line
level output. To use these turntables an d other line
devices like CD players, switch the input to Line.
3.
GND:
This screw connector should be used to secure
any turntables or other devices connected to the
mixer that need to be grounded.
4.
Line Inputs:
CD players, Tape Decks, Samplers or
other line level input devices should be connected to
these inputs.
5.
Record Output:
This RCA output is for connecting a
recording device such as a tape deck or CD recorder.
The level of the record output is based upon pre -
master levels.
6.
Master Output (RCA):
This output is for connecting
an external monitoring device such as a PA system,
powered monitors or a home stereo. The level of the
master stereo output signal is controlled by the
master fader.
7.
AC In:
This mixer is designed to work with the
power supply assembly that comes with the unit.
While the power is switched off, plug the power
supply into the mixer first, then plug it into the
outlet.
8.
Power Switch:
Use this switch to turn on the mixer
after all input devices are already connected to
prevent damage to your equipment. Turn the mixer
on before you turn on amplifiers and turn of
amplifiers before you turn off the mixer.
