NuAire Xboxer xbc+ Ecosmart Connect Control Installation Manual Download Page 36

36

21. 07. 20. Document Number  671954

Nuaire | 

Western Industrial Estate 

Caerphilly 

CF83 1NA 

|

 

nuaire.co.uk

XBC+ with Ecosmart Connect (C) Control

Installation Manual

8.0 FC BUS DEVICES

8.1 FAC Controller

A FAC Controller is used to control the unit. The controller can connect 
to the FC bus via the pin FC connection.

Address Type

Default Address

IP Address

192.168.92.68

Subnet Mask

255.255.255.0 (/24)

46 

47 

FAC Controller

MS/TP Router

8.1.1 MAC Address

The physical MAC address of the FAC adjustable between 4-127 
and is set via the DIP switch on the front of the unit. When multiple 
controllers are connected on the same FC bus, each controller ‘s MAC 
address must be unique.

8.1.2 BACnet Instance Number

The BACnet instance number of the FAC is factory-set to a random 
unique value from 0-4,194,304. This ensures that every controller will 
have a unique BACnet instance number on any possible network.

8.1.3 End Of Line (EOL) Resistor

When an FAC controller is used as a terminator at the end of a FC 
bus line, the EOL resistor dip switch can be switched on for best 
performance.

8.1.4 Fault Light Status

Blink 5Hz - 

 

Not all possible room modules are connected. This  

  is 

normal. 

Blink 2Hz - 

 

Startup in progress 

Off Steady - 

 

No Faults 

On Steady -

  

No Software

8.1.5 Current Loop DIP Switches

These should all be set to disabled. Enabling these switches will cause 
incorrect sensor values.

The BACnet router has a USB 2.0, Type B receptacle which is only used 
to obtain power from a computer or USB adapter. A mains adapter 
and cable is supplied. The router connects to the FC bus via screwed 
terminals.

8.2 BACnet IP to MS/TP Router (ESCO-IPN)

The BACnet IP to MS/TP Router exchanges information between 
networks and allows the controller to communicate on an IP network. 
One router is required for each MS/TP network.

A reset switch is available inside a small hole located on the side of the 
case. Pressing the reset switch with a paper clip (or similar device) for 
at least 1 second, resets the default values of the IP address, gateway 
address, and netmask. After you use the reset switch, you must reboot 
the router. The BACnet/IP to MS/TP Router contains a Web server. You 
can access the Web server from any Internet-compatible computer on 
the local network. To configure the router, you need a computer with 
an Ethernet connection, router, and standard Web browser.

8.3 Interconnection

The FC bus connects via the following MSTP cabling:

ESCO-MSTPC30M - 

 

Ecosmart Connect MSTP cable reel 30m 

ESCO-MSTPC150M -

  

Ecosmart Connect MSTP cable reel 150m

Suggested Wiring Colouring: 

White 

  

Green

    

Black 

  

COM 

Red 

  

Unused

On the SA Bus, the + and - wire are one twisted pair, and the COM and 
SA PWR are the second twisted pair of wires.

These cannot be used with RJ12 connections and must be stripped and 
connected using screwed terminals. The shield must be earthed at the 
control panel end only and be made continuous along the bus length. 
Room Modules must not be fitted more than 150metres (cable length) 
from the controller.

Summary of Contents for Xboxer xbc+ Ecosmart Connect Control





















































Reviews: