manualshive.com logo in svg

NuAire LabGard NU-581-400E, Operation And Maintenance Manual, Page: 77 / 108

Share
Download
NuAire LabGard NU-581-400E Operation And Maintenance Manual Download Page 77

OM0303 
Rev 5 July/2021 

Page 77 of 108 

8.2.2 

Calibration/Service Menu 

•

 

The Calibration/Service menu provides a list of sub-menu items to accomplish all service tasks.  Each sub-
menu item will be described in the following sections

 

•

 

Blower Setup:  

▪

 

The blower setup menu item provides an access to blower options and night setback setup 

Menu 

Blower 

options 

•

  Blower Options  

•

   Manual Blower Control 

This parameter allows 

ONLY THE CABINET TECHNICIAN

 to run the cabinet in manual mode.  This means 

with no controls or alarms activated.  When the manual control is on, the downflow and inflow displays 
will indicate nominal setpoints.  Airflow adjustments can be made in the manual mode by going into 
airflow calibration and adjusting the blower duty cycle.  The blower duty cycle will remain constant in 
manual mode.  The display will also indicate the manual control is activated.  When the manual control is 
off, full automatic control resumes. 

 
                                                

•

   Blower Lockout  

This parameter allows the access to turn the blower on or off to be restricted by the use of a password.  
When the blower lockout is on, pressing the blower icon will produce a numerical password screen. 
 

Summary of Contents for LabGard NU-581-400E













































































































Reviews:

No comments