manualshive.com logo in svg

Nuaire Group BPC MRXBOX95-WM1, Installation And Maintenance Manual

Share
Download
Nuaire Group BPC MRXBOX95-WM1 Installation And Maintenance Manual Download Page 8

8

09. 06. 16. Leaflet Number 671684

Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and 

dimensions of equipment and the right is reserved to make such changes without prior notice.

10.0 Replacement of Parts

Should any component need replacing Nuaire keep extensive stocks 
for quick delivery. Ensure that the unit is electrically isolated, before
carrying out any work.
Note: The supply cable must be replaced by an electrically 
competent person. 
When ordering spare parts, please quote the serial number of the
unit and the ARC number of the purchase if possible.

(This information will be available on the fan label).

11.0 Warranty

The 5 year warranty starts from the day of delivery and includes
parts and labour for the first year and parts only for the remaining 
4 years. This warranty is conditional on planned maintenance being
undertaken

.

12.0 Service Enquiries

Nuaire can assist you in all aspects of service. Our Technical Support
department will be happy to provide any assistance required. 

Technical Support 

on 029 2085 8400

Installation and Maintenance

The WM1 Wall Mounted Range of Units

Summary of Contents for BPC MRXBOX95-WM1















Reviews:

No comments

Brands by name

Popular brands

Load more brands