NSM PMG-DC Use And Maintenance Manual Download Page 10

RICERCA GUASTI

TROUBLE SHOOTING

manca tensione a vuoto

lack of no-load voltage

?

Avvolgimento in cto o difetto di isolamento o 
connessioni difettose. Controllare le resistenze degli 
avvolgimenti (vedi tabella) e l`isolamento: sostituire lo 
statore

?

perdita della magnetizzazione: sostituire "rorore con 
magneti

?

Short circuit in winding or fault insulation or loose 
connections. Check the windings resistances (as table) 
and the insulation: replace stator

?

loss of residual magnetism: replace rotor with magnets

Tensione a vuoto bassa

Too low no load voltage

?

Velocitá del motore troppo bassa: regolarla

?

Perdita parziale del magnetismo a seguito di elevato 
riscaldamento

?

Too low engine speed: adjust it

?

Loss of residual magnetism due to high overheating

Tensione a vuoto alta

Too high alternator no load voltage

?

Velocitá del motore troppo alta: regolarla

?

Too high engine speed: adjust it

Tensione corretta a vuoto ma bassa a carico.

Correct no-load voltage but low load voltage

?

Possibile sovraccarico: controllare la corrente di 
carico, rispristinare il carico corretto

?

Il motore rallenta: contattare il costruttore del motore; 
possibile scelta errata del motore

?

velocità a carico troppo bassa: regolarla

?

Possible overload: check value of load current, restore 
the correct load

?

The engine speed falls off: contact the engine 
specialist; too low engine power

?

Too low rotation speed: adjust it

Surriscaldamento della macchina

over heating

?

Circuito di ventilazione parzialmente ostruito: pulire

?

Possibile sovraccarico: controllare la corrente di 
carico, rispristinare il carico corretto

?

Ventilation inlet-outlet partially blocked: clean it

?

Possible overload: check value of load current, restore 
the correct load

Tensione instabile

Unstable voltage

?

Contatti incerti: controllare le connessioni

?

Irregolaritá di rotazione: verificare l'uniformitá di 
rotazione (contattare il costruttore del motore).

?

Loose contacts: check connections

?

Uneven rotation: check for uniform rotation speed 
(contact the engine specialist)

Macchina Rumorosa

Noisy Generator

?

Accoppiamento difettoso: verificare e riparare

?

Raschiamento statore/rotore: verificarne 
l'allineamento; contattare nostro Ufficio Tecnico

?

Poor coupling: check and repair

?

Scraping between stator and rotor: check aligniment; 
contact our technical dept

Summary of Contents for PMG-DC













Reviews: