manualshive.com logo in svg

Novus N1200, Instruction Manual

Share
Download
Novus N1200 Instruction Manual Download Page 12

Controller N1200  

NOVUS AUTOMATION 

12 / 13 

 

REDUCED REGISTERS TABLE  

FOR SERIAL COMMUNICATION 

Communication Protocol 

The  MOSBUS  RTU  slave  is  implemented.  All  configurable 
parameters  can  be  accessed  for  reading  or  writing  through  the 
communication  port.  Broadcast  commands  are  supported  as  well 
(address 0). 
The available Modbus commands are: 

03 - 

Read Holding Register

 

06 - 

Preset Single Register

 

05 - 

Force Single Coil

 

16 - 

Preset Multiple Register

 

Holding Registers Table

 

Follows a description  of the usual communication  registers. For full 
documentation  download  the  Registers  Table  for  Serial 
Communication  in  the  N1200  section  of  our  web  site  – 

www.novusautomation.com

. 

All registers are 16 bit signed integers.  

Address  Parameter 

Register Description 

0000  Active SP  Read:  Active  control  SP  (main  SP,  from 

ramp and soak or from remote SP). 
Write: to main SP. 
Range: from 

spll

 to 

spkl

. 

0001 

PV 

Read: Process Variable. 
Write: Not allowed. 
Range:  Minimum  value  is  the  one 
configured in 

spll

 and the maximum value 

is  the  one  configured  in 

spkl

.  Decimal 

point position depends on 

dppo

 value. 

In  case  of  temperature  reading,  the  value 
read  is  always  multiplied  by  10, 
independently of 

dppo

 value. 

0002 

MV 

Read: Output Power in automatic or manual 
mode. 
Write: Not allowed. See address 28. 
Range: 0 to 1000 (0.0 to 100.0 %). 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

SPECIFICATIONS  

DIMENSIONS

: ...................................... 48 x 48 x 110 mm (1 / 16 DIN) 

 ............................................................ Approximate Weight: 150 g  

CUTOUT IN THE PANEL

:  ................. 45.5 x 45.5 mm (+0.5 -0.0 mm) 

POWER SUPPLY

.................... 100 to 240 Vac/dc (±10 %), 50 / 60 Hz 

Optionally 24V: .................. 12 to 24 Vdc / 24 Vac (-10 % / +20 %) 
Maximum consumption: ........................................................  9 VA 

ENVIRONMENTAL CONDITIONS

: 

Operation Temperature: ...............................................  5 to 50 

C  

Relative Humidity: .......................................... 80 % max. @ 30 ºC 

For temperatures above 30 ºC, reduce 3 % for each ºC  

Internal  Use;  Category  of  installation  II,  Degree  of  pollution  2; 
altitude < 2000 m  

INPUT

 ............. T/C, Pt100, voltage and current (according to 

Table 1

)  

Internal Resolution: 

 .................................. 32767 levels (15 bits)  

Resolution of Display: 

.... 12000 levels (from - 1999 up to 9999)  

Rate of input reading: 

 ................................. up to 55 per second  

Precision: 

 . Thermocouples 

J

, 

K

, 

T

, 

E:

 0.25 % of the 

span

 

1 ºC  

 ................... Thermocouples 

N

, 

R

, 

S

, 

B

: 0.25 % of the 

span

 

3 ºC  

 ................................................................ Pt100: 0.2 % of the 

span

  

 .............................. 4-20 mA, 0-50 mV, 0-5 Vdc: 0.2 % of the 

span

  

Input Impedance:

 0-50 mV, Pt100 and Thermocouples: >10 M

 

 ................................................................................. 0-5 V: >1 M

 

 ................................................. 4-20 mA: 15 

 (+2 Vdc @ 20 mA) 

Measurement of Pt100: 

 ............... Three wire type, (

=0.00385)  

with  compensation  for  cable  length,  excitation  current  of  0.170 
mA.  
All input and output types are factory-calibrated. Thermocouples 
according to standard NBR 12771 / 99, RTD’s NBR 13773 / 97;  

ANALOGICAL OUTPUT (I/O5): 

 ..... 0-20 mA or 4-20 mA, 550

 max. 

31000 levels, insulated, for control or retransmission of PV and SP  

CONTROL OUTPUT: 

 

2 Relays SPST-NA (I/O1 and I/O2): 1.5 A / 240 Vac, general use  
 .......................... 1 Relay SPDT (I/O3): 3 A / 250 Vac, general use  
 .......................... Voltage pulse for SSR (I/O5): 10 V max. / 20 mA 
 ............. Voltage pulse for SSR (I/O3 and I/O4): 5 V max. / 20 mA 

ELECTROMAGNETIC COMPATIBILITY:

 ............... EN 61326-1:1997  

and EN 61326-1 / A1:1998 

SAFETY:

 ........................ EN61010-1:1993 and EN61010-1 / A2:1995 

USB 

INTERFACE 

2.0, 

CDC 

CLASS 

(VIRTUAL 

COMMUNICATIONS PORT), MODBUS RTU PROTOCOL. 
SPECIFIC CONNECTIONS FOR TYPE FORK TERMINALS OF 6.3 
MM;  
FRONT PANEL

: IP65, polycarbonate - UL94 V-2; 

 

CASE

: IP30, ABS+PC UL94 V-0;  

STARTS  UP  OPERATION

:  after  3  seconds  connected  to  the  power 

supply;

  

CERTIFICATIONS: 

 ........................................ CE / UL (FILE: 300526)

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for N1200














Reviews:

No comments

Brands by name

Popular brands

Load more brands