Novatel DL-V3 Reference Manual Download Page 92

Page: 92 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 3

DL-V3 Logs

3.10 METDEF

Meteorological Parameters

Structure:

Message ID = 150

Log Type: Polled

Table 65: Meteorological Log Status

3.11 PROJECTDEF

Project Definition

Structure:

Message ID = 156

Log Type: Polled

Field

Data

Description

Bytes

Format

Units

Offset

Header

Log header, see

Page 75

MetP

File position of the previous

metdefb

log

Ulong

bytes

Met Status

Meteorological log status
information, see

Table 65

Hexulong

H+4

Temp

Temperature, see also the
METTEMP command on

Page 58

Float

Celsius

H+8

Press

Pressure, see also the
METPRESS command on

Page 57

Float

hPa

H+12

Humid

Relative humidity, see also
the METHUMID command
on

Page 56

Float

H+16

Met Status Bit

Description

Bit=0

Bit=1

0x00000001

Temperature field flag

NOT VALID

VALID

0x00000002

Pressure field flag

NOT VALID

VALID

0x00000004

Humidity field flag

NOT VALID

VALID

Field

Data

Description

Bytes

Format

Units

Offset

Header

Log header, see

Page 75

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands