Novatel DL-V3 Reference Manual Download Page 57

Page: 57 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

2.29 METPRESS

Specify Air Pressure

The

metpress

command allows you to specify air pressure. Air pressure specified with the

metpress

command does not affect receiver operation. Rather, it allows you to create a record of atmospheric
conditions for post-processing purposes.

The

metpress

set

command specifies air pressure at

press

. This command only stores the pressure

value in volatile memory, and does not automatically generate a record. The humidity value can then
be displayed/recorded by requesting the

met

log.

The

metpress

clear

and the

metpress

default

commands clear the air pressure setting

Syntax

metpress

set [

press

]

metpress

default|clear

Message ID = 164

Table 38: METPRESS Default Configuration

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Pressure (in hectopascals or
kilopascals where:
1 kPa = 10 hPa)

Float

kPa or

hPa

a. You may use hPa or kPa in your float input depending on your preference

H+4

Parameter

Power-On

Freset

Stored in NVM

metpress

clear

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands