background image

Installation Manual for Infrared (IR) Receiver Kit (for Ceiling Suspended Type)

Model

CSIRK01

Applicable Indoor Unit Model

Ceiling Suspended Type

Applicable Wireless Controller

CIR01

Important Notice

 

Johnson Controls, Inc. pursues a policy of continuing improvement in design and performance in its 

products. As such, Johnson Controls, Inc. reserves the right to make changes at any time without prior 

notice.

 

Johnson Controls, Inc. cannot anticipate every possible circumstance that might involve a potential 

hazard.

 

This heat pump air conditioning unit is designed for standard air conditioning applications only.  

Do not use this unit for anything other than the purposes for which it was intended.

 

● The installer and system specialist shall safeguard against leakage in accordance with local pipefitter 

and electrical codes. The following standards may be applicable, if local regulations are not available. 

International Organization for Standardization: (ISO 5149 or European Standard, EN 378). No part of 

this manual may be reproduced in any way without the written consent of Johnson Controls, Inc. or 

York.

 

The heat pump air conditioning unit will be operated and serviced in the United States of America and 

comes with a full complement of the appropriate Safety, Danger, Caution, and Warnings.

 

If you have questions, please contact your distributor or dealer.

 

This manual provides common descriptions, and basic and advanced information to maintain and 

service this heat pump air conditioning unit which you operate, as well for other models.

 

This manual should be considered as a permanent part of the air conditioning equipment and should 

remain with the air conditioning equipment.

Product Inspection upon Arrival

1.  Upon receiving this product, inspect it for any damage incurred in transit. Claims for damage, either 

apparent or concealed, should be filed immediately with the shipping company.

2.  Check the model number, electrical characteristics (power supply, voltage, and frequency rating), and 

any accessories to determine if they agree with the purchase order.

3.  The standard utilization for this unit is explained in these instructions. Use of this equipment for 

purposes other than what it is designed for is not recommended. 

4.  Please contact your local agent or contractor as any issues involving installation, performance, or 

maintenance arise. Liability does not cover defects originating from unauthorized modifications 

performed by a customer without the written consent of Johnson Controls, Inc. and York. Performing 

any mechanical alterations on this product without the consent of the manufacturer will render your 

warranty null and void.

IMPORTANT:

READ AND UNDERSTAND THIS MANUAL BEFORE USING THIS INFRARED (IR) RECEIVER KIT. 

KEEP THIS MANUAL FOR FUTURE REFERENCE.

1

Summary of Contents for CSIRK01













Reviews: