manualshive.com logo in svg

Novacor Diasys Integra Access, Manual, Page: 32 / 42

Share
Download
Novacor Diasys Integra Access Manual Download Page 32

32 • 

Diasys Integra Access - Manual - GB - Rev 2

6

.

9. Display codes

As well as the display of the functioning mode, any
problems occuring during a measurement are indicated by
the display of an error code (see below) which is also noted
as such on the printed report if the software is not used.
If the DiasySoft software is used, these problems will be
detailed both on the computer screen and on the report. 

Display

Meaning

Comment

OSCI

Oscillometric mode

COMM

Communication established with printer or computer

MOD

Communication established with modem

GOOD

Modem transmission successful

TEST

Calibration test

STOP

Manual stopping of monitoring

Stop key held down

Er 01

Defective solenoid valve

Transitory electrical problem.  If problem 
continues, contact your distributor.

Er 02

Auto Calibration impossible

Residual pressure in cuff.  Check air tubing.  
If problem continues, contact your distributor.

Er 03

Abnormal inflation

Tubing disconnected, bent, pierced or blocked 
or cuff too loose.  Check the air tubing and 
connector and that the cuff is properly wound 
around patient’s arm.

Er 04

Measurement not validated

Diastole < 50mm not confirmed

Er 05

Abnormal pressure variation

Muscular contraction or excessive exercise.

Er 07

Excessive measurement time

Measurement time >120 s.

Er 09

Excessive cuff pressure 

Er 10

Excessive noise or artefacts

Interference on signal;  measurement 
impossible

Er 11

Systolic pressure 

≤

50mmHg

Er 12

Diastolic pressure 

≤

30mmHg

Er 14

Battery run down

Er 15

Not used

Er 16

Stopped by connection

Recording stopped because cable link 
connected to Diasys.

Er 17

Measurement stopped manually

Stop key pressed during measurement

Er 18

Stopped by switching mode selector   Mode selector switched from measurement 

position to programming position

Er 19

Impossible to process oscillometric shapes

Er 25

Heart rate unstable during measurement

Er 26

Error during modem transmission (cf. chapter 7.2)

Er 27

Connection to number called impossible during transmission (cf. chapter 7.2)

Manuel Access GB.qxd  24/02/2004  11:32  Page 32

Summary of Contents for Diasys Integra Access











































Reviews:

No comments