Nortik Navigator Assembly Instruction Manual Download Page 14 | Manualshive

Page: 14 / 28

background image

14

Make sure, that the flaps for the thigh
braces are not jammed behind the side
elements.

Install cross rib #3 just as #5.

Insert ridge bar into the cross rib.

Take the thigh braces and slide on the
neoprene sleeves.

Note

: This is a one-time installation for

your new boat.

TIP:

Put some dish liquid into the

neoprene sleeve to put it on easier.

(shown on the thigh braces of the nortik
argo)

«
...
12
13
14
15
16
...
»

Summary of Contents for Navigator





























Reviews:

No comments

Related manuals for Navigator

Brand: Anacortes Yacht Charters Pages: 15

Brand: MSSC Pages: 28

Brand: Blue Wave Boats Pages: 1

TomCat 255 Pilothouse

Brand: C-Dory Marine Pages: 20

Brand: Spitfire Pages: 10

Brand: Monterey Boats Pages: 126

Brand: Boston Whaler Pages: 82

SEASCOOTER AQUA RANGER SD95001

Brand: Sea-doo Pages: 16

Brand: Prestige Pages: 112

Brand: Gnom Rov Pages: 27

Brand: FitNord Pages: 84

Brand: Quicksilver Pages: 55

Brand: NorthStar Pages: 56

Brand: stellar labs Pages: 7

Brand: Hobie Pages: 29

Brand: Rave Sports Pages: 13

Brand: Silver Marine Pages: 13

Brand: Silver Marine Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands