NorthStar DOC0056 Installation Instructions Manual Download | Manualshive

Page: 13 / 21

background image

OPEN

Figure 13 The 19inch Brackets

Note:

Use the outer holes to attach the 19inch Brackets.

5.

Tighten the screws to a torque of 6 Nm.

Document Number:

INS-0038

Revision:

A

Prepared by:

Mikael Lindevall

Date:

2012-04-26

Approved by:

Ulf Krohn

Status:

RELEASED

Page 11

«
...
11
12
13
14
15
...
»

Summary of Contents for DOC0056






















Reviews:

No comments

Related manuals for DOC0056

Brand: HAMPTON BAY Pages: 11

Brand: Happybeds Pages: 5

Brand: feather&black Pages: 4

Brand: EAST COAST Pages: 12

Brand: EAST COAST Pages: 5

Brand: EAST COAST Pages: 10

Brand: Hanover Pages: 4

Brand: FUFU & GAGA Pages: 30

Spellbinding Witch Sisters

Brand: Home Accents Pages: 5

Brand: Jack-Post Pages: 13

Brand: TIMBER ART DESIGN Pages: 8

Double Pedstal Style Table

Brand: Amish Tables Pages: 2

Brand: Germania Pages: 8

Brand: Lorell Pages: 3

Bibliotheque Broc Edition 131331

Brand: atmosphera Pages: 2

Brand: De La Espada Pages: 7

Brand: Nacon Pages: 8

Brand: Tee-Zed Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands