NorthStar DOC0056 Installation Instructions Manual Download

Page: 3 / 21

OPEN

NTRODUCTION

This document describes how to install the Indoor Cabinets.

1.1

ARGET

ROUP

The target group for this document is the personnel involved in
the installation and maintenance of the site.

1.2

REREQUISITES

All performance statement in this document relies on the following:



Only approved hardware are used





Proper hardware handling





Installation and maintenance instructions as well as

documentation for external equipment are followed



1.3

OOLS AND

QUIPMENT

The following tools are required for the installation:



Screwdriver Torx T30





U-wrench 13mm





U-wrench 10mm





Torque set, 5-25Nm





Torque set, 20-100Nm



Document Number:

INS-0038

Revision:

Prepared by:

Mikael Lindevall

Date:

2012-04-26

Approved by:

Ulf Krohn

Status:

RELEASED

Page 1

Summary of Contents for DOC0056






















Search results

Summary of Contents for DOC0056

Reviews:

Related manuals for DOC0056

Brands by name

Popular brands

NorthStar DOC0056, Installation Instructions Manual

Search results

Summary of Contents for DOC0056

Reviews:

Related manuals for DOC0056

Brands by name

Popular brands