Nortel Enterprise Edge Manual Download Page 112

112

  ISDN PRI

Enterprise Edge Feature Programming Telephone Guide

P0908510 Issue 01

Your Enterprise Edge system sends the Business Name concatenated with the set 
name on an outgoing call but only after the Business Name has been programmed.

The available features include:

Receiving Connected Name

Receiving Calling Name

Receiving Redirected Name

Sending Connected Name

Sending Calling Party Name

Consult your customer service representative to determine which of these features 
is compatible with your service provider.

Name and number blocking for PRI

When activated, 

ƒ°⁄·

 allows you to block the outgoing name 

and/or number on a per-call basis. Name and number blocking can be used with an 
Enterprise Edge set.

Consult your customer service representative to determine whether or not this 
feature is compatible with your provider.

Emergency 911 Dialing

Enterprise Edge with the ISDN PRI feature is capable of transmitting the telephone 
number and internal extension number of a calling station dialing 911 to the Public 
Switched Telephone Network. State and local requirements for support of 
Emergency 911 Dialing service by Customer Premises Equipment vary. Consult 
your local telecommunications service provider regarding compliance with 
applicable laws and regulations.

If transmission of internal extension numbers is not required or desired, then it is 
recommended that you maintain a site map or location directory that allows 
emergency personnel to rapidly locate an Enterprise Edge set given its DID number. 
This list should be kept up to date and readily available, and can be included in the 
Programming Record.

2-way DID

With PRI the same lines can be used for receiving direct inward dialing (DID) and 
for making direct outward dialing (DOD) calls.

The dialing plan configured by your customer service representative determines 
how calls are routed.

Consult your customer service representative to determine whether or not this 
feature is compatible with your service provider.

Summary of Contents for Enterprise Edge











































































































































































Reviews: