manualshive.com logo in svg

Nortel 2332 Series, Installation Manual

Share
Download
Nortel 2332 Series Installation Manual Download Page 8

8

NN47250-307 (324136-A Version 01.03)

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

RF Radiation Exposure & Hazard Statement

To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the 
antenna of the device will be greater than 20 cm (8 in.) away from all persons. Using higher gain antennas and types of 
antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of 
the product must adhere to the installation instructions provided in this manual.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Non-Modification Statement

Use only the supplied internal antenna, or external antennas supplied by the manufacturer. Unauthorized antennas, 
modifications, or attachments could damage the WLAN 2332-A1 and related Series 2332 access points and violate FCC 
regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void 
the user's authority to operate this equipment. Contact Nortel for a list of approved 2.4 GHz and 5.0 GHz external 
antennas.

This device must be operated with the CAT-5 Ethernet cable installed on each activated Ethernet Port of a Series 2332 
access point to ensure compliance with the Class B emissions standards. Failure to comply with this installation 
requirement may cause the device to operate in excess of the allowable emissions limits.

Deployment Statement

This product is certified for indoor deployment only. 

Do not

 install or use this product outdoors.

Dynamic Frequency Selection 

(DFS) 

in the 5.0 GHz UNII bands

The 2332-A1 access point has been prohibited, via software, from operating in the 5250 to 5350 MHz and 
5470 to 5725 MHz frequency bands for the US and Canada because it cannot meet the DFS requirements as outlined in 
the rules of the FCC for Part 15, Subpart E that come into force on July 20, 2007.

Canadian IC Statement

Operation is subject to the following two conditions in Canada:

1) this device may not cause interference, and

2) this device must accept any interference, including interference that may cause undesired operation of the 
device

To prevent radio interference to the licensed service (i.e. co-channel Mobile Satellite systems) this device is intended to 
be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is 
installed outdoors is subject to licensing and not supported by the WLAN Access Point 2332-A1.

Summary of Contents for 2332 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands