background image

Doc No. 700016  Page   of 16 

 

Part No. 700016 

Nortek Global HVAC (UK) Limited,  Fens Pool Avenue,  Brierley Hill,  West Midlands,  DY5 1QA 

WARNINGS 

 

Nortek Global HVAC (UK) Ltd equipment must be installed and maintained in accordance with 
the relevant provisions of the Gas Safety (Installations and Use) Regulations 1998 for gas fired 
products. Due account should also be taken of any obligations arising from the Health and 
Safety at Works Act 1974 or relevant codes of practice. In addition the installation must be 
carried out in accordance with the current IEE wiring regulations (BS 7671), BS 6896 (Industrial 
& Commercial) and any other relevant British Standards and Codes of Practice by a qualified 
installer. All external wiring MUST comply with the current IEE wiring regulations.  

A

A

MBI

MBI

R

R

AD

AD

 

 

V

V

ISION

ISION

 

 

VSX

VSX

 

 

R

R

ADIANT

ADIANT

 

 

T

T

UBE

UBE

 

 

H

H

EATER

EATER

 

 

A

A

SSEMBLY

SSEMBLY

 

 

I

I

NSTRUCTION

NSTRUCTION

 

 

M

M

ANUAL

ANUAL

 

 

INDEX

                                                                                        

Section 

 

Introduction and Document Index 

Installation Requirements -------------------------------------------------- 1 

Assembly Instructions ------------------------------------------------------- 2 

User and Operating Instructions ------------------------------------------ 3 

Summary of Contents for Ambirad Vision VSX

















Reviews: