24
25
Änderungen, die dem technischen Fortschritt dienen, sowie Irrtümer vorbehalten!
ORIGINALBETRIEBSANLEITUNG
NORSUP
DE
EN
NL
FR
DK
SE
WWW.NORSUP.EU
Änderungen, die dem technischen Fortschritt dienen, sowie Irrtümer vorbehalten!
SALZWASSER ELEKTROLYSE TYPE OCEANCLEAR LS
SALZWASSER ELEKTROLYSE TYPE OCEANCLEAR LS
3
2. INSTALLATION DIAGRAM
I
The electrical connections at cell-level must not point upwards, to avoid any deposits of water or humidity
on them.
The pH corrector container must be installed a safe distance away from any electrical device or any other
chemicals.
4
4
17
4
10
8
KEY :
UNO
model
: white.
DUO
model
: white + grey.
PRO
model
: white + grey +
black
.
1
: Salt / temperature / low water sensor (optional)
2
: Cell
3
: Electronics unit
4
: Filter with ballast
5
: Peristaltic pump
6
: Pool Ground (optional)
7
,
8
: Probe holder
9
: Injection connector
10
: ORP probe
11
: pH probe
12
,
13
: Bracket
14
,
15
: Semi-flexible tubing
9
1
7
6
19
H
16
18
2
3
13
20
22
5
12
11
14
15
ELEMENTS NOT SUPPLIED :
16
: Electrical power supply
17
: pH corrector container
18
: Copper cable
19
: Filter
20
: Ground rod
21
: Heat pump
22
: Filtration pump
21
3. SCHALTKASTEN
3.1. ERSTE INBETRIEBNAHME
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
3.2. TASTATUR
1. GERÄTEFUNKTIONEN
2. INSTALLATIONSSCHEMA
• Die elektrischen Anschlüsse der Zelle dürfen nicht nach oben ausgerichtet sein, um zu verhindern, dass sich Wasser
oder Feuchtigkeit auf ihnen niederschlägt.
• Der Kanister mit dem pH-Regulierung ist in ausreichender Entfernung von elektrischen Geräten und anderen
chemischen Produkten zu lagern.
Modell
Chlorproduktion
durch Elektrolyse
pH-Wert-Regulierung
Kontrolle
der Chlorproduktion mit
ORP-Sonde
UNO
DUO
PRO
1: Sensor zur Messung Salzgehalt /
Temperatur / zu wenig Wasser
(optional)
2:
Zelle
3:
Schaltkasten
4: Ballastfilter
5:
Peristaltikpumpe
6: Pool-Erdungsset (optional)
7,8: Sondenträger
9: Einspritzanschluss
10: ORP-Sonde
11: pH-Sonde
12,13: Halterung
14,15: Halbstarrer Schlauch
LEGENDE :
Modell UNO : weiß
Modell DUO : weiß + grau
Modell PRO : weiß + grau + schwarz
NICHT IM LIEFERUMFANG
ENTHALTENE ELEMENTE :
16: Stromversorgung
17: Kanister für pH-Regulierung
18: Kupferkabel
19: Filter
20: Erdspieß
21: Wärmepumpe
22: Filtrationspumpe
AUFEINANDERFOLGENDE
MENÜS
MÖGLICHE EINSTELLUNGEN
NAVIGATION
• Français
• English
• Deutsch
• Español
• Italiano
• Nederlander
• Portugués
Für jeden Parameter ein
Datenelement mit den Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
• On line
• Dashboard
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
STEUERUNGSTASTE
(JE NACH MODELL)
FUNKTION
• Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
• Ausschalten des Schaltkastens (drücken und halten).
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
• Zugriff auf die Menüs..
Einschalten des Boost-Modus für 24 Stunden.
• Anzeige der Wassertemperatur für einige Sekunden (nur wenn die
Standardanzeige auf « Anzeige On line » eingestellt ist).
• Direkter Zugriff auf das Menü « » (drücken und halten).
• Anzeige des Salzgehalts für einige Sekunden (nur wenn die Standardanzeige auf «
Anzeige On line » eingestellt ist).
• Direkter Zugriff auf das Menü « » (drücken und halten).
g
Diese Taste ist nur bei den Modellen
DUO und PRO vorhanden.
• Direkter Zugriff auf das Menü « » (drücken und halten).
Auswahl eines Werts oder eines Datenelements.
• Stornierung einer Eingabe.
• Zurück zum vorherigen Menü.
• Ausschalten des Boost-Modus.
• Bestätigung eines Eintrags.
• Aufrufen eines Menüs.
• Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. SCHALTKASTEN
3.1. Erste Inbetriebnahme
Beim ersten Einschalten des Schaltkastens die folgende Programmierung durchführen.
Aufeinanderfolgende
Menüs
Mögliche Einstellungen
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
Für jeden Parameter ein Datenelement mit den
Tasten
auswählen, dann mit der Taste
OK
bestätigen.
10 bis 200 m
3
, in 10er-Schritten.
Tag / Monat / Jahr
Stunde / Minute
On line
Dashboard
3.2. Tastatur
STEUERUNGSTASTE
(Je nach Modell)
FUNKTION
MENU
Einschalten des Schaltkastens.
Einige Minuten nach dem Einschalten startet die Produktion automatisch (mit oder
ohne ORP-Kontrolle).
Ausschalten des Schaltkastens
(drücken und halten)
.
Beim Ausschalten erlöschen das Display und die grüne Leuchtanzeige, die rote
Leuchtanzeige geht an.
Wenn ein Alarm ausgelöst wird, drücken Sie zuerst auf , um ihn auszuschalten.
Zugriff auf die Menüs.
BOOST
Einschalten des Boost-Modus für 24 Stunden.
T°C
Anzeige der Wassertemperatur für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
SALT
Anzeige des Salzgehalts für einige Sekunden
(nur wenn die Standardanzeige auf
« Anzeige On line » eingestellt ist)
.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
pH
Diese Taste ist nur bei den Modellen
DUO
und
PRO
vorhanden.
Direkter Zugriff auf das Menü «
»
(drücken und halten)
.
Auswahl eines Werts oder eines Datenelements.
Stornierung einer Eingabe.
Zurück zum vorherigen Menü.
Ausschalten des Boost-Modus.
OK
Bestätigung eines Eintrags.
Aufrufen eines Menüs.
Bestätigung eines Alarms.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.
4
3. ELECTRONICS UNIT
3.1. First commissioning
When switching on the electronics unit for the first time, carry out the following programming.
Successive
menus
Possible settings
Navigation
Français
English
Deutsch
Español
Italiano
Nederlander
Portugués
For each parameter, select a data item with the
buttons, then confirm with the
OK
button.
From 10 to 200 m
3
, in increments of 10.
Day / Month / Year
Hour / Minute
In line
Dashboard
3.2. Keypad
COMMAND KEY
(depending on
model)
FUNCTION
MENU
Switching on the electronics unit.
A few minutes after switching on, production starts automatically (with or without ORP
check).
Switching off the electronics unit
(press and hold)
.
When switching off, the screen and the green LED turn off while the red LED comes on.
If an alarm has been activated, press first on to switch off.
Access the menus.
BOOST
Boost mode starts for 24 hours.
T°C
Water temperature display for a few seconds
(only if the default display is set to « In line
display »)
.
Direct access to the «
» menu
(press and hold)
.
SALT
Salt level display for a few seconds
(only if the default display is set to « In line display »)
.
Direct access to the «
» menu
(press and hold)
.
pH
This command key is only present on the
DUO
and
PRO
models.
Direct access to the «
» menu
(press and hold)
.
Selecting a value or data element.
Cancellation of an entry
Back to previous menu.
Stopping Boost mode.
OK
Command confirmation.
Entering a menu.
Dismissing an alarm.