background image

6

•  Avoid installation above gas ranges or stoves.
•  Avoid installation between the kitchen fan and stove. If oily 

fumes or a large amount of steam are present in the installation 

location, take measures to prevent the fumes and steam from 

entering in the equipment.

•  Install in a location where the exhaust gas flow will not be affected 

by fans or range hoods.

•  Take care that noise and exhaust gas will not affect neighbors.  

Avoid installation on common walls as the unit will make some 

operational noises while it is running.

• 

Before installing, make sure that the exhaust flue termination will 

have the proper clearances according to 

the National Fuel Gas 

Code (ANSI Z223.1-latest edition) or the Natural Gas and Propane 

Installation Code (CSA B149.1).

•  If the unit is installed in a location with very high humidity, conden 

sate may form inside the unit and/or cause incomplete combustion, 

damage to the electrical components, or electric leakage.

State of California: The water heater must be braced, anchored or strapped to avoid moving during an 

earthquake. Contact local utilities for code requirements in your area or call: 1-855-960-3434 and 

request instructions.

Be sure to do

Prohibited

Prohibited

CAUTION

The Commonwealth of Massachusetts: The water heater can be used for hot water only and not in a 

combination of domestic and space heating.

For Venting Manufacturers Requirements, see websites listed below:

Noritz N-Vent                          www.noritz.com

•  The water heater is designed for indoor installation only. Never install it 

outdoors or in a bathroom, it may be damaged or a fire may be caused.

•  Consult with the customer concerning the location of installation.
• 

Install the water heater in an area that allows for the proper clearances 

to combustible and noncombustible construction. Consult the rating 

plate on the appliance for proper clearances.

•  Do not install the water heater in a place where it may be threatened by 

falling objects, such as under shelves.

•  The water heater must be installed in a place where supply and exhaust 

pipes can be installed as directed.

•  Do not install the water heater where the exhaust will blow on outer walls 

or material not resistant to heat. Also consider the surrounding trees and 

animals.

The heat and moisture from the water heater may cause discoloration of 

walls and resinous materials, or corrosion of aluminum materials.

Prohibited

Summary of Contents for GQ-C2857WS-FF US











































Reviews: