Nordpeis CC-RON00-1X0 Ronda 160, User Manual

Page: 12 / 36

12 GB
fresh air supply set is also recommended . Insufficient
air supply can cause down-draught and thereby low
combustion efficiency and the problems that this
entails: soot stains on the glass, inefficient use of the
wood and a soot deposits in the chimney.
Floor plate
A fireproof floor plate must be put in front of the fireplace
if the floor is of a combustible material.
Dimensional drawing
The illustrations indicate the approximate centre height
of the hole for the flue. Distortions in floors and walls
may influence the dimensions. Dry stack the fireplace
without glue for accurate height and positioning of the
flue/chimney connection.
3. Technical Information
All products Nordpeis have secondary combustion and
are clean burning. The combustion takes place in two
phases: First the wood burns and then the gases from
the fumes are lit by the hot air. This ensures that these
new fireplaces have minimal emissions of soot particles
and un-burnt gases (such as CO) and are thus better
for the environment. Clean burning fireplaces require
a small amount of wood in order to obtain a good heat
output. Use exclusively clean and dry wood.
Surround Ronda 160
Insert NI-26
Material insert Steel/Cast iron
Surface treatment
door / doorframe
Heat resistant varnish
Fuel Wood logs, 30 cm
Nominal output 5 kW
Efficiency
79,3%
CO % @ 13% O
2
0,07
Draught system Air vent control
Combustion system
Secondary combustion
(clean burning)
Heating area 60-120 m²
Flue outlet Top
Flue
Inner Ø 150 mm
(NB! In UK outer Ø)
Weight of insert 93 kg
Weight of surround 239 kg
Area of convection
air vent under insert
400 cm²
Area of convection
air vent over insert
500 cm²
Flue gas temperature 313 °C
Air supply
requirements (m³/h)
11
Fuel charge
1,4 kg
Refueling interval
56 min
Opening of the air
vent control
50%
Operation Intermittent*
* Intermittent combustion refers to normal use of a fireplace,
i.e. new wood is inserted when the previous load has burned
down to ember
4. Safety distances
Ensure that the safety distances are complied with
(FIG 1).
When connecting a steel chimney to the top outlet
follow the assembly instructions from the producer.
Ensure to comply with the security distances required
for the steel chimney.
5. Assembly
Assembly instructions for the insert (FIG 2 - FIG 12)
The following tools are necessary:
•
5 mm Allen key
•
13 mm spanner/wrench
•
Caulking gun (for the stove cement)
1.
Ensure that all the loose parts are included (FIG 2):
A. Insert with door and heat shield
B. 4 legs with adjusting bolts and lock nuts
C. 4 fastening bolts with disks for the legs
D. Handle for ash grate and ashtray
E. Glove
F. Assembly instructions
G. Warranty card
2. Carefully lay the insert on its back. Ensure that the
transportation padding is put inside the insert before
turning it over, so that the insulating plates in the
burn chamber do not fall down and break. Please
note that the insulating plates may release coloured
dust when touched. Avoid touching the cast iron with
dust on your fingers. In case of dust on any cast iron
part, the glove included is well suited to brush it off.
Start with assembling the legs (FIG 3) as follows:
•
Fasten the screws on to the insert with a 13 mm
spanner/wrench. The legs are placed as shown (the
opening in the legs should face outwards).
•
Use the adjusting bolts (FIG 4) and adjust the legs
to the desired height (X) before returning the insert
to an upright position (do not tilt the insert). The
height depends on the surround.
Regulation of leg height (X) for NI-26:
From
: 20 mm
To
: 160 mm.
•
Flue outlet
NI-26 is delivered standard with a top flue outlet collar.