background image

ENgLIsH

CONNECTION AND MAINTENANCE OF VENTILATION

The control unit and the plant must be installed and connected by authorized personnel according to the standards in force

 

(see chapter GENERAL PRECAUTIONS).

ATTENTION: the control unit and the feeding cable must not be in contact with hot parts.

Our  products  are  equipped  with  tangential  fans  suitable  to  improve  the  distribution  of  heat  through  the  ventilation  exclusively  of  the 

installation room (see chapter TECHNICAL DATA SHEET). 

The lighting and the adjustment is carried out through the proper standard supplied control unit that has to be installed far from any direct 

heat source.

The selection of the kind of insert to be connected is in the control unit and has to be done by moving the small bridge 

7

 as shown hereafter 

before the INSERT starts to operate (see chapter SERIES VENTILATION). 

This operation must be done without electric energy!!

On our products, it is possible to install OPTIONAL ventilation kits suitable to improve the distribution of heat by ventilation only either of the 

installation room or of the adjacent local (see chapter VENTILATION HOOD OR ADJACENT LOCAL). 

For the connection of the ventilation kit, please see the instructions manual CONNECTION AND MAINTENANCE OF VENTILATION OPTIONAL.

CONNECTION

: Connect the power supply cable of the control unit to a bipolar switch respecting at least a 3 mm distance between the 

contacts (power supply 230 V~ 50 Hz, it is necessary to provide for the correct connection to the grounding plant). 

This operation must be 

done without electric energy!!

WARNINg:

 The COMMAND must be connected to the mains with a differential line cut-off switch according to the regulations in 

force. Correct operation of the command is assured only for the proper motor for which it has been manufactured. 

Improper use 

relieves the manufacturer from each responsibility

.

ALLOWED / NOT ALLOWED FUELs

Allowed fuels are logs. Use exclusively dry logs (max. content of water 20%). Maximum 3 logs should be loaded. The pieces of wood 

should have a length of ca. 20-30 cm and a maximum circumference of 30-35 cm.

Compressed not worked-out wood briquettes must be used carefully to avoid overheating that may damage the device, 

since these have a very high calorific value

.

The wood used as fuel must have a humidity content lower than the 20% and must be stored in a dry place. Humid wood tends to burn 

less easily, since it is necessary a greater quantity of energy to let the existing water evaporate. Moreover, humid content involves 

the disadvantage that, when temperature decreases, the water condensates earlier in the hearth and therefore in the stack causing 

a remarkable deposit of soot with following possible risk of fire of the same.

Fresh wood contains about 60% of H

2

O, therefore it is not suitable to be burnt. 

It is necessary to place this wood in a dry and ventilated place (for example under a roofing) for at least two years before using it.

Besides others, it is not possible to burn: carbon, cuttings, waste of bark and panels, humid wood or wood treated with 

paints, plastic materials; in this case, the warranty on the device becomes void.

 

Paper and cardboard must be used only to light the fire.

The combustion of waste is FORBIDDEN 

and would even damage the appliance and the flue, causing health damages and claims 

by the neighborhood owing to the bad smell. 

The wood is not a fuel which allows a continuous operation of the appliance, as consequence the heating all over the night is not 

possible.

Variety

kg/mc

kWh/kg 

moistness

 20%

Beech

750

4,0

Oak

900

4,2

Elm

640

4,1

Poplar

470

4,1

Larch*

660

4,4

spruce*

450

4,5

scots pine *

550

4,4

*

  RESINOUS WOOD NOT SUITABLE FOR THE BURNING 

ATTENTION : the continuous and protracted use of aromatic wood (eucalyptus, myrtle etc.) quickly damages  the 

cast iron parts (cleavage) of the product

.

The declared technical data have been achieved by burning beech wood class “A1” according to the requirement UNI EN ISO 17225-5 and wood 

moisture content less than 20%. By burning a different kind of wood the efficiency of the product itself could change and some specific adjustments 

on the appliance could be needed.

26

Summary of Contents for INSERTO 100 Crystal




































Reviews: