Nordic ID Morphic User Manual Download Page 9 | Manualshive

Page: 9 / 58

background image

(iv) CE Compliance Statement

Hereby, Nordic ID Oy, declares that the
NORDIC ID Morphic models are in compliance
with the essential requirements and other
relevant provisions of Directive 1999/5/EC

(v) FCC Compliance Statement

This hand-held device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the hand-held equipment

The FCC ID information is printed on the back side of your hand-held.

Nordic ID International Headquarters

Myllyojankatu 2A
FI-24100 SALO
FINLAND

Phone:

+358 2 727 7700

Fax:

+358 2 727 7720

Email: [email protected]

www.nordicid.com

«
...
7
8
9
10
11
...
»

Summary of Contents for Morphic



























































Reviews:

No comments

Related manuals for Morphic

Brand: Tanca Pages: 22

Brand: Gallagher Pages: 13

Brand: IDTECK Pages: 12

Brand: Baracoda Pages: 23

Brand: Socket Pages: 38

Brand: Alien Pages: 41

Brand: Newland Pages: 22

Brand: HIKVISION Pages: 22

PowerScan PM9500

Brand: Datalogic Pages: 40

Brand: Motorola Pages: 44

Brand: ITLONG Pages: 7

Brand: Obreey Pages: 107

Brand: BBPOS Pages: 2

Brand: Orbit Research Pages: 73

Brand: SICK Pages: 132

IS-TH1 RG Series

Brand: i.safe MOBILE Pages: 64

Brand: PerkinElmer Pages: 2

Brand: Leuze electronic Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands