background image

6

DEVICE OPERATION

Turning On the Device

Press and hold the on/off button for 1.5 seconds. The LEDs will blink. After 

a long and a short beep, battery life and sensitivity indicator LEDs as well 

as the alarm button LEDs (if they are activated) will stay lit up. The device 

is ready for use.

WARNINGI!

 Keep the device away from metal objects when turning it on.

NOTE:

 In case the device emits a continuous alarm, press the on/off button 

once to reset it. 

Resetting the Alarm

If the device starts emitting an alarm without the presence of a metal object, press the 

on/off button once to reset the alarm.

Sensitivity Setting

The sensitivity setting consists of 3 levels:

Each time you press the sensitivity button the level changes and the white LEDs indicate the sensitivity 

level.

Sensitivity setting should be adjusted according to the target metal size and maximum operating 

distance.

Large Metal Objects:

 Low Sensitivity Setting

Medium Size Metal Objects:

 Medium Sensitivity Setting

Small Metal Objects:

 High Sensitivity Setting

For metal sizes, NIJ Standard - 0602.02 has been taken as a reference.

Alarm Selection

Audio Alarm 

You can activate the audio alarm by pressing the audio alarm button once. The LED on the 

button will light up solid. To turn off the alarm press the button again. The LED will go off.

Vibration Alarm

You can activate the audio alarm by pressing the vibration alarm button once. The LED on 

the button will light up solid. To turn off the alarm press the button again. The LED will go 

off.

NOTE

: The audio and vibration alarms can be activated separately or at the same time or they can 

both be turned off to have a silent operation.

1 White LED:

Low Sensitivity

2 White LEDs:

Medium Sensitivity

3 White LEDs:

High Sensitivity

Summary of Contents for MAKRO NMS20

















Reviews: