manualshive.com logo in svg

Nokia NPM-10 Series, Troubleshooting Instructions, Page: 42 / 48

Share
Download
Nokia NPM-10 Series Troubleshooting Instructions Download Page 42

NPM-10

Troubleshooting Instructions RF

CCS Technical Documentation

Page 42

 

Nokia Corporation          Confidential

Issue 1 03/2003

Sweeptime 10 msec 

RF Attenuation: 30 dB

Reference level: if you set this to 40 dBm, you can tune both the low band (target output 
power of 32.0 dBm for power level 5) and highband (target output power of 29.5 dBm 
for power level 0) at the maximum output levels. The reference level must be reduced, to 
say 0 dB level when tuning the base level.

Trigger: Video. Set the level to 0 dbm. This must be lowered when you are setting the 
base level (Base level target output power of -30 dBm). If you don't lower the video trig-
ger level to below –30 dBm when tuning the base level, the spectrum analyzer will not 
be triggered when you are tuning the base level.

Center Frequency: 836.6 MHz (For GSM 850 band, channel 190 is used for Tx output 
power tuning).  For GSM 1900, Center frequency is 1880 MHz (mid Channel 661) for Tx 
output power tuning.

Summary of Contents for NPM-10 Series

















































Reviews:

No comments