manualshive.com logo in svg

Nokia 7110, Manual, Page: 3 / 30

Share
Download
Nokia 7110 Manual Download Page 3

CONFIDENTIAL

3 (30)

NSE-5

Service & Analysis Center Europe

Repairhints

Version 1.0 Approved

SACE AMS Training Group

30.07.2000

Repairhints_nse5_002508

Checked by:
AMS TRAINING GROUP

Approved by:
SACE

1.

 

INTRODUCTION

IMPORTANT:

This document is intended for use by authorized NOKIA service centers only.

The purpose of this  document is to provide some further service information for NOKIA 7110 phones.
It contains a lot of collected tips and hints to find failures and repair solutions easily.
It will also give support to the inexperienced technicians.
Saving process time and improving the repair quality is the aim of using this document.
We have build it up based on fault symptoms (listed in "Contents") followed by detailed description for further
analysis.
It is to be used additionally to the service manual and other service information like Service Bulletins, for that
reason it doesn't contain any circuit descriptions or schematics.

All measurements are made using following equipment:

Nokia repair SW  

: WinTesla Version 6.43

DLL version

: NSE5 version 271.03.00 / 19.07.2000

Nokia Module Jig

: MJS-8

Digital multimeter  

: Fluke 73

Oscilloscope

: Hitachi V-1565; Fluke PM 3380A/B

Spectrum Analyzer

: Advantest R3361C with an analogue probe

RF-Generator /

: Rohde & Schwarz CMD 53

GSM Tester

While every endeavour has been made to ensure the accuracy of this document, some errors may exist. If any errors
are found by the reader, NOKIA should be notified in writing, using following procedure:

Please state:

Title of the Do Issue Number/Date of publication.
Page(s)  and/or Figure(s) in error.

Please send to:

Nokia GmbH

Service & Analysis Center Europe
Meesmannstr.103
D-44807 Bochum / Germany
Email: [email protected]

Summary of Contents for 7110































Reviews:

No comments