Nokia 7110 Manual Download Page 21

Page: 21 / 30

CONFIDENTIAL

21 (30)

NSE-5

Service & Analysis Center Europe

Repairhints

Version 1.0 Approved

SACE AMS Training Group

30.07.2000

Repairhints_nse5_002508

Checked by:
AMS TRAINING GROUP

Approved by:
SACE

TX FAILURE

GSM 900 faulty

GSM1800 faulty

Check 13MHz RFCLK at N700,

pin15 (+/-50Hz). Change if

faulty.

Check 116 MHz at

N700, pin 44/45

Check 116 MHz at N600, pin

25/26

Check UHF 2036 MHz

at N600, pin 4

Check PA_GSM

(902MHz) at

N600,pin22

Check

PA_GSM(902MHz) at

N500,pin1

Check PA_GSM at

N500,pin4

Check 232MHz at

N700,pin 46

Check 232Mhz at

N600,pin 35/37

Check UHF 1979,8MHz

at N600,pin4

Check PA_PCN

(1747,8MHz)at

N600,pin 40

Check PA_PCN at

N501,pin1

Check PA_PCN at

N501,pin4

Check VHF 464MHz at

N700, pin 8

Change N700

Check Z702

Check/change G700

Change N600

Check Z601 (in/out)

Check Z603,N502,Z502

Change G702

Check PA_GSM at L500,

Z500/503, X500/501

Check at N500/501,pin2:

CTL_GSM=0,7-1,7Vpp

CTL_PCN=0,12-0,2Vpp

( squarewave, depends on PWR-level )

Check PA_PCN at

Z504-Ant-conn.

Check/change L503

Check VC at Z504

(0,9VDC squarewave)

Change Z504

notOK

Check PA_PCN at Z503,

X500/501

Check at N503: a).BAND_SEL

(lowlevel)on pin2, b).VTX

(2.8Vpulsed)on pin 1

notOK

Check/change

a) N600, b) N100 (pin24)

if notOK, MAD faulty

notOK

YES

Summary of Contents for 7110































Search results

Summary of Contents for 7110

Reviews:

Nokia 7110, Manual, Page: 21 / 30

Search results

Summary of Contents for 7110

Reviews: