Nokia 7110 Manual Download Page 17

Page: 17 / 30

CONFIDENTIAL

17 (30)

NSE-5

Service & Analysis Center Europe

Repairhints

Version 1.0 Approved

SACE AMS Training Group

30.07.2000

Repairhints_nse5_002508

Checked by:
AMS TRAINING GROUP

Approved by:
SACE

NO SERVICE GSM 900 -

First Check spectrum if it is only a RX failure , see spectrum charts.

REF: GSM 900: Ch60 (947 MHz) / GSM 1800: Ch700 (1842,8 MHz).

WINTESLA TUNING RX CALIBRATIONS

Failed to set

high reference

Check 71 MHz

IF at C617/618

Check 71 MHz

IF at

N700,pin37/38

Check 13MHz

IF in/out at

Z701

Check 13MHz

IF at N700 pin

23/24

Change COBBA

( N200 )

Check 13MHz

Ref.frequency at

G701,N700, pin15

(+/- 50Hz)

Check GSM

LNA 947MHz

at N600,pin27

Check 947

MHz in/out at

Z600

Check UHF

2036 MHz at

N600 Pin3

Check UHF

2036 MHz at

G700

Check Vc&Vcc

at G700

Change G701

Check

Z500/503

Change Z600

Change N600

Failed to set low

reference

Change G700

Change Z700

Change Z701

Change N700

NOTE : If COBBA has been changed, SIMLOCK & IMEI

data must be set. Also realign RX/TX values esp.TX

I/Q.

notOK

Summary of Contents for 7110































Search results

Summary of Contents for 7110

Reviews:

Nokia 7110, Manual, Page: 17 / 30

Search results

Summary of Contents for 7110

Reviews: