manualshive.com logo in svg

Nokia 7110, Manual, Page: 25 / 30

Share
Download
Nokia 7110 Manual Download Page 25

CONFIDENTIAL

25 (30)

NSE-5

Service & Analysis Center Europe

Repairhints

Version 1.0 Approved

SACE AMS Training Group

30.07.2000

Repairhints_nse5_002508

Checked by:
AMS TRAINING GROUP

Approved by:
SACE

MICROPHONE DOES NOT WORK

-Also see SB 018 –

Note : First of all check the mechanical condition of the phone and slide for mechanical
damage or stuck. (PogoPins).

Probable reasons:

-

 

Shorts between contact tracks and slideflex.
These shorts often occur at the end of the slide-cover (friction-dust).
If this happens, clean the flex with dustfree cloth, especially in the bottom corner.

-

 

The Pogo pins in microphone housing get stuck. If this happens, change
A-Cover.

-

 

Check the internal contact springs from Pogo-pins and their connector pads
on the PCB.

-

 

Check impedance (~ 1,8k) , change slide cover if necessary.

-

 

Check solderings of Z103/104, C106/107/132.

-

 

Check signals (given over MPA-1 =audio test probe ) at V100 in & out.

-

 

Check V_COBBA at V111 (2,8VDC).

-

 

Check voltage ( during call ) at C117/121 ( 1,4VDC ) , at E100 ( 0,3V ), E101 ( 1,8V ).

-

 

Change COBBA if all of the above works.

Rewriting of IMEI and SIMlock data is necessary after changing the COBBA!

-

 

If the error persists, MAD or PCB should be the reason.

Summary of Contents for 7110































Reviews:

No comments