Nixie Clock MOD-SIX Updating Instructions Download | Manualshive

Page: 15 / 20

background image

3

Version history

Note: Gaps in version numbers indicate unreleased development

versions.

3.1

Clock version history

•

V06-06 - Version shipped with original GEN I clocks

•

V07-07 - Version shipped with GEN II clock kits

•

V07-09 - Version shipped with assembled GEN II clocks

•

V07-53 - Version shipped with GEN IIv7 clocks

•

V08-08 - Version shipped with GEN IIv8 (SLW) clocks, latest version

3.2

GPS repeater version history

•

V10 - Version shipped with GEN II clocks and GEN I upgrade kits

•

V26 - Version shipped with GEN IIv7 clocks

•

V27 - Version shipped as an update for GEN IIv7 clocks

•

V36 - Version shipped with GEN IIv8 (SLW) clocks with word
dictionary, latest version

3.3

Keyfob version history

•

V12 - Version for prototype (Sparkfun) hardware

•

V14 - Version shipped with GEN IIv8 (SLW) clocks, latest version

3–1

«
...
13
14
15
16
17
...
»

Summary of Contents for MOD-SIX





















Reviews:

No comments

Related manuals for MOD-SIX

Brand: Crosley Pages: 6

IP Solutions VIP-A12DS

Brand: Valcom Pages: 3

Brand: La Crosse Technology Pages: 5

Brand: jWIN Pages: 3

Brand: La Crosse Technology Pages: 24

Brand: La Crosse Technology Pages: 10

Brand: Icon Time Systems Pages: 12

Brand: InfoTronics Pages: 40

Brand: Marathon Pages: 4

Brand: Philips Pages: 2

CHIPDRIVE extern

Brand: TOWITOKO Pages: 48

Brand: Discovery Expedition Pages: 17

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 4

Brand: Equity Pages: 4

Brand: VTech Pages: 23

Brand: E-Bench Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands