background image

10

Spindle Arbor

Sleeve

Pull out

Turn the Sleeve
to the left

Align

Spindle Arbor

Sleeve

White line

Depression

Pilot pin

Cutter

0RXQWLQJ5HPRYLQJ&XWWHU

WARNING

:HDUVDIHW\JORYHVZKHQUHSODFLQJFXWWHU

CAUTION

'R QRW XVH DQ\ RWKHU FRPELQDWLRQV RI 3LORW

3LQ DQG FXWWHU WKDQ WKRVH VKRZQ LQ WKH
FRPSDWLELOLW\WDEOH

(1)

  

Bring the Drill Motor up by turning the Rod Handle 

clockwise. (Fig. 10)

Downward

Upward

Fig. 10

(2)  Insert a Pilot Pin, appropriate 

for the cutter size, into the 
cutter. (Fig.11)

 Fig. 

11

(3)  Align the depression in the 

cutter with the white line on 
the Sleeve, and then insert the 
cutter.

 

When you insert the cutter 
far enough the Sleeve will 
turn clockwise and lock with a 
clicking sound.

 

* When you find it hard to 
i n s e r t   t h e   c u t t e r,   t u r n   t h e 
Sleeve counterclockwise and 
do over. (Fig.12)

 Fig. 

12

(4)  To remove the cutter, turn the 

Sleeve counterclockwise.  The 
cutter will come off. (Fig.13)

 Fig. 

13

3UHSDUDWLRQRI&XWWLQJ2LO

Cutting Oil Safety Precautions

WARNING

8VH

 Use Cutting Oil for cutting purpose only.  Don’t use it 

for household purposes

+DQGOLQJ3UHFDXWLRQV

 The Cutting Oil contains amine.  Do not mix it up 

with rust inhibitor, etc. containing nitrite.

 Wear safety glasses for eye protection when 

KDQGOLQJ&XWWLQJ2LOH\HLQMXU\PD\UHVXOWVLILWJHWV

into your eyes. 

 Wear protective gloves for hand protection when 

KDQGOLQJ &XWWLQJ 2LO VNLQ LQMXU\ PD\ UHVXOW LI LW

comes into contact with your skin. 

 Wear respirator when exposure to respiratory 

hazards with oil mist or vapor is anticipated.  
Inhalation of oil mist or vapor may make you feel 
sick. 

 When diluting Cutting Oil, follow the instructions per 

the Operation Manual.

 Keep Cutting Oil out of reach of children.

 Don’t drink Cutting Oil.

)LUVW$LG

 If Cutting Oil gets into your eyes, immediately open 

your eyelids with your fingers and wash your eyes 
with plenty of water for at least 15 minutes.  If your 
eyes feel irritated, consult with a medical doctor and 
follow his/her instructions.

 If Cutting Oil comes into contact with your skin, 

immediately wash it away with plenty of water and 
soap.  Take off contaminated clothes.  Clean the 
clothes if you need to wear it again.  If your skin 
feels irritated, consult with a medical doctor for 
medical instructions.

 If someone inhales oil mist or vapor, immediately 

take him/her to an area where fresh air is abundant 
and wrap up his/her body with a blanket, etc. to 
keep body temperature.  Have him/her take a 
rest and consult with a medical doctor for medical 
instructions.

 If someone drinks Cutting Oil, immediately make 

him/her drink plenty of water and vomit it.  Consult 
with a medical doctor for medical instructions.  When 
unconscious, do not pour water into his/her mouth 
nor induce him/her to vomit.

,QVWUXFWLRQVLQ&DVHRI)LUH

,IÀUHEUHDNVRXWLQWKHYLFLQLW\ZHDU33(SHUVRQDO

protective equipment) and use foam, powder or 
CO

2

 fire extinguisher to put the fire out from the 

windward.

Summary of Contents for ATRA ACE AO-5575A

























Reviews: